HHLONIX
EN

Israel · Bezeq

Can I use my own router with Bezeq?

Yes. Bezeq documents PPPoE with a line-dependent VLAN with your account's broadband login. Check phone and TV services before you remove the provider box.

Ethernet cable and network connections
Illustrative photograph; equipment and compatibility may differ.Amin · CC BY-SA 4.0 · Wikimedia Commons
Page reviewed 6 November 2026Profile researched 6 November 2026Cited sources 4How Hlonix verifies →

Quick reference

Own-router settings at a glance

From official provider sources cited below. Pick your router for a full verdict with topology and caveats.

Bezeq Bfiber (GPON) — own ONT/router from Bezeq's approved list

Own-router path
Depends on line authentication and router
Physical handoff
Fibre GPON → approved ONT (bridge/SFP/gateway) → router
WAN connection
PPPoE
VLAN
Confirm with provider
ISP phone / voice
Check with your provider
ISP TV
Check with your provider
Evidence confidence
Medium — verify account details

Settings to enter on your router

  1. Check that your ONT or ONT-gateway model AND firmware version appear on Bezeq's approved GPON equipment list (SFP ONTs such as Nokia G-010S-A/Q, bridge ONTs such as Nokia G-010G-P/Q or ZTE F601, or gateways such as AVM FRITZ!Box 5530/5590/5690); unapproved devices may be blocked.
  2. Connect the fibre to the approved ONT (or insert the approved SFP ONT into your router's SFP port); with a bridge ONT, run Ethernet from the ONT to your router's WAN port.
  3. On the router, set the WAN connection type to PPPoE.
  4. Enter the PPP username from your ISP including the @provider suffix, and the PPP password your ISP gave you (e.g. Partner sends them by SMS).
  5. Enable NAT and keep-alive, save, and let the router reconnect.
WAN authPPPoE
VLANVaries — confirm for your line
Priority / PCP—
MTUDefault

What Bezeq officially documents

Check that your ONT or ONT-gateway model AND firmware version appear on Bezeq's approved GPON equipment list (SFP ONTs such as Nokia G-010S-A/Q, bridge ONTs such as Nokia G-010G-P/Q or ZTE F601, or gateways such as AVM FRITZ!Box 5530/5590/5690); unapproved devices may be blocked. Connect the fibre to the approved ONT (or insert the approved SFP ONT into your router's SFP port); with a bridge ONT, run Ethernet from the ONT to your router's WAN port. On the router, set the WAN connection type to PPPoE. Enter the PPP username from your ISP including the @provider suffix, and the PPP password your ISP gave you (e.g. Partner sends them by SMS). Enable NAT and keep-alive, save, and let the router reconnect.

Before you remove the Bezeq box

The official page does not settle phone service for a third-party router — confirm before you disconnect the provider box. TV services may use their own VLAN or box; check before swapping. Bezeq states private equipment may join Bfiber if it is on its published approved list; approval covers only the listed firmware versions and Bezeq may disconnect unapproved devices. VLAN ID and MTU for fibre: not stated. The PPPoE + username@ISP-suffix scheme comes from Bezeq's own (DSL-era) ASUS router guide; Bezeq's fibre pages do not restate the WAN protocol, so confirm with your ISP. Israel splits infrastructure (Bezeq) from ISP (e.g. Partner, Cellcom, Bezeq International) — credentials come from the ISP, not Bezeq. Approved-list PDF is undated (firmware codes suggest 2025).

Common setup mistakes

Choose PPPoE, not Dynamic IP — the line will not come up with DHCP alone. The VLAN depends on the access network behind your line — confirm it with the provider before configuring the router. Username is the PPP username issued by your internet provider (ISP) followed by @ and that provider's suffix (per Bezeq's router guide). Power-cycle the ONT or modem after swapping routers so it releases the old session.

Next step

Evidence

Page reviewed 6 November 2026 · profile researched 6 November 2026.