Poland · Play (incl. UPC)
Can I use my own router with Play (incl. UPC)?
Yes. Own router connects directly. Check phone and TV services before you remove the provider box.

Quick reference
Own-router settings at a glance
From official provider sources cited below. Pick your router for a full verdict with topology and caveats.
Play Internet Światłowodowy — own router (DHCP)
- Own-router path
- Own router connects directly
- Physical handoff
- Fibre → Ethernet WAN
- WAN connection
- Not published — ask the provider
- VLAN
- Confirm with provider
- ISP phone / voice
- Check with your provider
- ISP TV
- Check with your provider
- Evidence confidence
- Medium — verify account details
Settings to enter on your router
- Connect your router to a computer by cable and open its admin page (login on the router's sticker).
- Set the WAN/Internet interface to obtain an IPv4 address automatically (DHCP / Dynamic IP).
- If you are on the Internet Światłowodowy or Internet Światłowodowy 2 tariff, leave VLAN tagging off.
- On any other Play fibre tariff, enable VLAN tagging on WAN with VLAN ID 35.
- Save, connect the router to the line and allow 20–30 minutes for it to receive an IP address.
Instant verdict for your router:eero 6+Deco X50/X55ASUS RT-AX86U ProArcher BE550Orbi RBK760Nest Wifi ProOther router
Play / ex-UPC cable — own router behind Connect Box in modem (bridge) mode
- Own-router path
- Gateway stays — use bridge/modem mode
- Physical handoff
- Cable modem (Connect Box / Giga Connect Box / Ubee EVW3226) in modem mode → own router
- WAN connection
- Handled by the cable modem
- VLAN
- Confirm with provider
- ISP phone / voice
- Check with your provider
- ISP TV
- Check with your provider
- Evidence confidence
- Medium — verify account details
Settings to enter on your router
- Log in to the modem with the password printed on its underside.
- Open the modem operating-mode tab, enable modem mode (Włącz tryb modemu) and save.
- Connect your own router's WAN port to the modem by Ethernet and set WAN to automatic IP (WAN protocol not stated on the page — confirm with Play).
- To check the modem later, open 192.168.100.1 or 192.168.0.1.
Instant verdict for your router:eero 6+Deco X50/X55ASUS RT-AX86U ProArcher BE550Orbi RBK760Nest Wifi ProOther router
Other Polish ISPs:Compare all Polish ISP settings
What Play (incl. UPC) officially documents
Connect your router to a computer by cable and open its admin page (login on the router's sticker). Set the WAN/Internet interface to obtain an IPv4 address automatically (DHCP / Dynamic IP). If you are on the Internet Światłowodowy or Internet Światłowodowy 2 tariff, leave VLAN tagging off. On any other Play fibre tariff, enable VLAN tagging on WAN with VLAN ID 35. Save, connect the router to the line and allow 20–30 minutes for it to receive an IP address. Log in to the modem with the password printed on its underside. Open the modem operating-mode tab, enable modem mode (Włącz tryb modemu) and save. Connect your own router's WAN port to the modem by Ethernet and set WAN to automatic IP (WAN protocol not stated on the page — confirm with Play). To check the modem later, open 192.168.100.1 or 192.168.0.1.
Before you remove the Play (incl. UPC) box
The official page does not settle phone service for a third-party router — confirm before you disconnect the provider box. TV services may use their own VLAN or box; check before swapping. Page lists conditions but does not spell them out; PPPoE, MTU, IPv6, voice and TV not stated. No page date shown. Play does not support third-party equipment beyond these parameters.
Common setup mistakes
If the provider device must stay, put your own router behind it and avoid double NAT: use the provider's bridge, modem or passthrough option where one exists, otherwise run your router in access-point mode.
Next step
Evidence
- Play — Jak podłączyć własny router do sieci (official help) (official ISP)
- Play — Jak ustawić tryb bridge w routerze Play (official help) (official ISP)
Page reviewed 6 November 2026 · profile researched 6 November 2026.