HHLONIX
EN

Denmark · Hiper

Can I use my own router with Hiper?

Yes. Hiper documents DHCP / IPoE on VLAN 101.

Network equipment and server rack
Illustrative photograph; equipment and compatibility may differ.Shixart1985 · CC BY 2.0 · Wikimedia Commons
Page reviewed 6 November 2026Profile researched 6 November 2026Cited sources 2How Hlonix verifies →

Quick reference

Own-router settings at a glance

From official provider sources cited below. Pick your router for a full verdict with topology and caveats.

Hiper Fiber — own router straight on the fibre box (DHCP, VLAN 101)

Own-router path
Own router connects directly
Physical handoff
Fibre box (ONT) → Ethernet WAN
WAN connection
DHCP
VLAN
VLAN 101 (802.1Q tagged)
ISP phone / voice
No dependency documented
ISP TV
No dependency documented
Evidence confidence
High — official provider source

Settings to enter on your router

  1. Connect the router's WAN port to the fibre box (or keep Hiper's router and use bridge mode instead).
  2. Set WAN connection type to automatic IP / DHCP (Dynamic IP); do not clone MAC.
  3. Enable VLAN (802.1Q) tagging on the Internet/WAN with VLAN ID 101 and priority 0 (on TP-Link/ASUS this sits in the IPTV/VLAN menu with a custom/manual profile).
  4. Save and reboot; no PPPoE login is needed.

Copy-paste router configuration

Generated from the settings above. Menu names vary by firmware version.

OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan.101'
uci set network.wan.proto='dhcp'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restart
MikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/interface vlan add name=wan-vlan101 vlan-id=101 interface=ether1
/ip dhcp-client add interface=wan-vlan101 disabled=no
/interface list member add list=WAN interface=wan-vlan101
UniFi
  1. Settings → Internet → select the WAN (Primary) → Advanced: Manual.
  2. VLAN ID: on, 101.
  3. IPv4 connection: DHCP.
  4. Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
  1. Interfaces → VLANs (OPNsense: Interfaces → Other Types → VLAN): parent = WAN NIC, tag 101, priority 0.
  2. Interfaces → Assignments: assign the new VLAN as WAN.
  3. WAN → IPv4 configuration type: DHCP.
  4. Save, apply, then power-cycle the ONT/modem.
ASUS
  1. WAN → Internet Connection → WAN Connection Type: Automatic IP.
  2. LAN → IPTV → Select ISP Profile: Manual → Internet: VID 101, PRIO 0.
  3. Apply and reboot the ONT/modem.
TP-Link
  1. Advanced → Network → Internet: connection type Dynamic IP.
  2. Advanced → Network → IPTV/VLAN: enable, Mode Custom, Internet VLAN ID 101.
  3. Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
  4. Save and restart the ONT/modem.
FRITZ!Box
  1. Internet → Account Information → Internet service provider: Other Internet service provider.
  2. Connection: external modem or router (LAN 1 as WAN).
  3. Account information required: No.
  4. Use VLAN for internet access: on, VLAN ID 101.
  5. Apply and restart the ONT/modem.
eero / Nest
  1. eero app → Settings → Network settings → ISP settings: leave on automatic/DHCP; VLAN ID 101.
  2. Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: DHCP; VLAN 101 where your firmware offers it.

Hiper HybridFiber (coax) / phone-line — own router behind Hiper router in bridge mode

Own-router path
Gateway stays — use bridge/modem mode
Physical handoff
Hiper router (bridge mode) → Ethernet → own router
WAN connection
Handled by the provider gateway
VLAN
Handled by provider device
ISP phone / voice
No dependency documented
ISP TV
No dependency documented
Evidence confidence
Medium — verify account details

Settings to enter on your router

  1. Keep Hiper's router connected to the cable-TV or phone socket.
  2. Put the Hiper router into bridge mode using Hiper's bridge-mode guide.
  3. Connect your own router's WAN port to the Hiper router.
  4. Check your connection type under Mit Abonnement in Mit Hiper first.
WAN authDHCP / IPoE
VLAN101 (802.1Q tagged)
Priority / PCP0
MTUDefault

What Hiper officially documents

Connect the router's WAN port to the fibre box (or keep Hiper's router and use bridge mode instead). Set WAN connection type to automatic IP / DHCP (Dynamic IP); do not clone MAC. Enable VLAN (802.1Q) tagging on the Internet/WAN with VLAN ID 101 and priority 0 (on TP-Link/ASUS this sits in the IPTV/VLAN menu with a custom/manual profile). Save and reboot; no PPPoE login is needed. Keep Hiper's router connected to the cable-TV or phone socket. Put the Hiper router into bridge mode using Hiper's bridge-mode guide. Connect your own router's WAN port to the Hiper router. Check your connection type under Mit Abonnement in Mit Hiper first.

Before you remove the Hiper box

The official page does not settle phone service for a third-party router — confirm before you disconnect the provider box. No TV dependency is documented. Router must support VLAN tagging. Hiper gives brand guides for TP-Link, Deco, ASUS, Netgear Nighthawk and Ubiquiti but provides no support for own equipment. MTU and IPv6 not stated. Not for 5G or HybridFiber lines.

Common setup mistakes

Choose Dynamic IP / DHCP (IPoE), not PPPoE — there is no broadband login to enter. Tag the WAN with VLAN 101; a missing or wrong tag is the most common reason a new router gets no connection. 802.1Q tag enabled Power-cycle the ONT or modem after swapping routers so it releases the old session.

Next step

Evidence

Page reviewed 6 November 2026 · profile researched 6 November 2026.