HHLONIX
EN

Spain · Movistar

Can I use my own router with Movistar FTTH?

For an internet-only setup behind a separate ONT, Movistar-hosted technical guidance documents PPPoE on VLAN 6. Full IPTV/VoIP replacement is substantially more complex because those services use additional VLANs and customer-specific settings.

Ethernet cable and network connections
Illustrative photograph; equipment and compatibility may differ.Wikideas1 · CC0 1.0 · Wikimedia Commons
Page reviewed 6 November 2026Dataset snapshot 23 September 2026Cited sources 2How Hlonix verifies →

Quick reference

Own-router settings at a glance

From official provider sources cited below. Pick your router for a full verdict with topology and caveats.

Movistar FTTH — own router behind ONT

Own-router path
Own router connects directly (medium-confidence evidence)
Physical handoff
Movistar ONT → Ethernet WAN
WAN connection
PPPoE
VLAN
VLAN 6 (802.1Q tagged)
ISP phone / voice
Check with your provider
ISP TV
Check with your provider
Evidence confidence
Medium — verify account details

Settings to enter on your router

  1. For internet-only use, Movistar-hosted community guidance documents PPPoE on VLAN 6 with priority 1.
  2. Movistar IPTV and VoIP use additional VLANs and service-specific configuration.
  3. Keep the Movistar router available if TV/voice support or provider diagnostics are required.

Copy-paste router configuration

Generated from the settings above. Use the broadband username and password from your provider account or welcome email. Menu names vary by firmware version.

OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci add network device
uci set network.@device[-1].type='8021q'
uci set network.@device[-1].ifname='wan'
uci set network.@device[-1].vid='6'
uci set network.@device[-1].name='wan.6'
uci set network.@device[-1].egress_qos_mapping='0:1'
uci set network.wan.device='wan.6'
uci set network.wan.proto='pppoe'
uci set network.wan.username='YOUR_BROADBAND_USERNAME'
uci set network.wan.password='YOUR_BROADBAND_PASSWORD'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restart
MikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/interface vlan add name=wan-vlan6 vlan-id=6 interface=ether1
/interface pppoe-client add name=pppoe-out1 interface=wan-vlan6 user="YOUR_BROADBAND_USERNAME" password="YOUR_BROADBAND_PASSWORD" add-default-route=yes use-peer-dns=yes disabled=no
/interface list member add list=WAN interface=pppoe-out1
/ip firewall mangle add chain=postrouting out-interface=pppoe-out1 action=set-priority new-priority=1 passthrough=yes comment="ISP requires 802.1p priority 1"
UniFi
  1. Settings → Internet → select the WAN (Primary) → Advanced: Manual.
  2. VLAN ID: on, 6. Priority 1 is required — use a UniFi version that offers a QoS/CoS tag field, otherwise UniFi is not a fit.
  3. IPv4 connection: PPPoE — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
  4. Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
  1. Interfaces → VLANs (OPNsense: Interfaces → Other Types → VLAN): parent = WAN NIC, tag 6, priority 1.
  2. Interfaces → Assignments: assign the new VLAN as WAN.
  3. WAN → IPv4 configuration type: PPPoE, username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
  4. Save, apply, then power-cycle the ONT/modem.
ASUS
  1. WAN → Internet Connection → WAN Connection Type: PPPoE; enter username YOUR_BROADBAND_USERNAME and password YOUR_BROADBAND_PASSWORD.
  2. LAN → IPTV → Select ISP Profile: Manual → Internet: VID 6, PRIO 1.
  3. Apply and reboot the ONT/modem.
TP-Link
  1. Advanced → Network → Internet: connection type PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD).
  2. Advanced → Network → IPTV/VLAN: enable, Mode Custom, Internet VLAN ID 6, Internet VLAN priority 1.
  3. Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
  4. Save and restart the ONT/modem.
FRITZ!Box
  1. Internet → Account Information → Internet service provider: Other Internet service provider.
  2. Connection: external modem or router (LAN 1 as WAN).
  3. Account information required: Yes — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
  4. Use VLAN for internet access: on, VLAN ID 6, PBit 1.
  5. Apply and restart the ONT/modem.
eero / Nest
  1. eero app → Settings → Network settings → ISP settings: PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD); VLAN ID 6.
  2. Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: PPPoE; VLAN 6 where your firmware offers it.
  3. eero and Nest do not document priority tags or option 60 — they are not a reliable fit for this profile.
Internet authPPPoE
Internet VLAN6 / priority 1
VoIP VLAN3 in cited guidance
IPTV VLAN2 in cited guidance

Internet-only is the simple case

A capable router can create the internet WAN interface on VLAN 6 and establish PPPoE behind the ONT.

Triple-play needs more than one WAN

Movistar-hosted guidance describes separate WAN interfaces for internet, voice and IPTV, including static/customer-specific IPTV values and routing requirements.

Why Hlonix stays conservative

This is advanced provider-hosted community guidance. Hlonix treats the internet path as medium-confidence and does not claim a simple TV/voice replacement.

Next step

Evidence

Page reviewed 6 November 2026 · compatibility dataset snapshot 23 September 2026.