HHLONIX
EN

Czechia · T-Mobile CZ

Can I use my own router with T-Mobile CZ?

Yes. T-Mobile CZ documents PPPoE on VLAN 2510 and generic login values. Check phone and TV services before you remove the provider box.

Ethernet cable and network connections
Illustrative photograph; equipment and compatibility may differ.Swpb · CC BY-SA 4.0 · Wikimedia Commons
Page reviewed 6 November 2026Profile researched 6 November 2026Cited sources 2How Hlonix verifies →

Quick reference

Own-router settings at a glance

From official provider sources cited below. Pick your router for a full verdict with topology and caveats.

T-Mobile T FIBER (own FTTH network) — own router, PPPoE VLAN 2510

Own-router path
Own router connects directly
Physical handoff
Fibre (G-PON / XGS-PON) ONT → Ethernet WAN
WAN connection
PPPoE
VLAN
VLAN 2510 (802.1Q tagged)
ISP phone / voice
Check with your provider
ISP TV
Check with your provider
Evidence confidence
High — official provider source

Settings to enter on your router

  1. Connect the router's WAN port to the T FIBER optical terminal.
  2. Select PPPoE as the WAN connection type.
  3. Enable VLAN on the WAN interface: VLAN ID 2510, 802.1p priority 0.
  4. Enter username fiber and password fiber.

Copy-paste router configuration

Generated from the settings above. Generic values published by the provider — any non-empty value is accepted where the provider says so. Menu names vary by firmware version.

OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan.2510'
uci set network.wan.proto='pppoe'
uci set network.wan.username='fiber'
uci set network.wan.password='fiber'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restart
MikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/interface vlan add name=wan-vlan2510 vlan-id=2510 interface=ether1
/interface pppoe-client add name=pppoe-out1 interface=wan-vlan2510 user="fiber" password="fiber" add-default-route=yes use-peer-dns=yes disabled=no
/interface list member add list=WAN interface=pppoe-out1
UniFi
  1. Settings → Internet → select the WAN (Primary) → Advanced: Manual.
  2. VLAN ID: on, 2510.
  3. IPv4 connection: PPPoE — username fiber, password fiber.
  4. Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
  1. Interfaces → VLANs (OPNsense: Interfaces → Other Types → VLAN): parent = WAN NIC, tag 2510, priority 0.
  2. Interfaces → Assignments: assign the new VLAN as WAN.
  3. WAN → IPv4 configuration type: PPPoE, username fiber, password fiber.
  4. Save, apply, then power-cycle the ONT/modem.
ASUS
  1. WAN → Internet Connection → WAN Connection Type: PPPoE; enter username fiber and password fiber.
  2. LAN → IPTV → Select ISP Profile: Manual → Internet: VID 2510, PRIO 0.
  3. Apply and reboot the ONT/modem.
TP-Link
  1. Advanced → Network → Internet: connection type PPPoE (username fiber, password fiber).
  2. Advanced → Network → IPTV/VLAN: enable, Mode Custom, Internet VLAN ID 2510.
  3. Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
  4. Save and restart the ONT/modem.
FRITZ!Box
  1. Internet → Account Information → Internet service provider: Other Internet service provider.
  2. Connection: external modem or router (LAN 1 as WAN).
  3. Account information required: Yes — username fiber, password fiber.
  4. Use VLAN for internet access: on, VLAN ID 2510.
  5. Apply and restart the ONT/modem.
eero / Nest
  1. eero app → Settings → Network settings → ISP settings: PPPoE (username fiber, password fiber); VLAN ID 2510.
  2. Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: PPPoE; VLAN 2510 where your firmware offers it.

T-Mobile internet over CETIN optical converter — own router, PPPoE VLAN 848

Own-router path
Own router connects directly
Physical handoff
CETIN optical converter → Ethernet WAN
WAN connection
PPPoE
VLAN
VLAN 848 (802.1Q tagged)
ISP phone / voice
Check with your provider
ISP TV
Check with your provider
Evidence confidence
High — official provider source

Settings to enter on your router

  1. Connect the router's WAN port to the CETIN optical converter.
  2. Set WAN service type PPPoE over Ethernet.
  3. Enable VLAN with 802.1Q VLAN ID 848 and 802.1P priority 0.
  4. Set MTU to 1492.
  5. Enter PPP username adsl and password adsl.

Copy-paste router configuration

Generated from the settings above. Generic values published by the provider — any non-empty value is accepted where the provider says so. Menu names vary by firmware version.

OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan.848'
uci set network.wan.proto='pppoe'
uci set network.wan.username='adsl'
uci set network.wan.password='adsl'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restart
MikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/interface vlan add name=wan-vlan848 vlan-id=848 interface=ether1
/interface pppoe-client add name=pppoe-out1 interface=wan-vlan848 user="adsl" password="adsl" add-default-route=yes use-peer-dns=yes disabled=no
/interface list member add list=WAN interface=pppoe-out1
UniFi
  1. Settings → Internet → select the WAN (Primary) → Advanced: Manual.
  2. VLAN ID: on, 848.
  3. IPv4 connection: PPPoE — username adsl, password adsl.
  4. Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
  1. Interfaces → VLANs (OPNsense: Interfaces → Other Types → VLAN): parent = WAN NIC, tag 848, priority 0.
  2. Interfaces → Assignments: assign the new VLAN as WAN.
  3. WAN → IPv4 configuration type: PPPoE, username adsl, password adsl.
  4. Save, apply, then power-cycle the ONT/modem.
ASUS
  1. WAN → Internet Connection → WAN Connection Type: PPPoE; enter username adsl and password adsl.
  2. LAN → IPTV → Select ISP Profile: Manual → Internet: VID 848, PRIO 0.
  3. Apply and reboot the ONT/modem.
TP-Link
  1. Advanced → Network → Internet: connection type PPPoE (username adsl, password adsl).
  2. Advanced → Network → IPTV/VLAN: enable, Mode Custom, Internet VLAN ID 848.
  3. Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
  4. Save and restart the ONT/modem.
FRITZ!Box
  1. Internet → Account Information → Internet service provider: Other Internet service provider.
  2. Connection: external modem or router (LAN 1 as WAN).
  3. Account information required: Yes — username adsl, password adsl.
  4. Use VLAN for internet access: on, VLAN ID 848.
  5. Apply and restart the ONT/modem.
eero / Nest
  1. eero app → Settings → Network settings → ISP settings: PPPoE (username adsl, password adsl); VLAN ID 848.
  2. Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: PPPoE; VLAN 848 where your firmware offers it.
WAN authPPPoE
VLAN2510 (802.1Q tagged)
Priority / PCP0
MTUDefault

What T-Mobile CZ officially documents

Connect the router's WAN port to the T FIBER optical terminal. Select PPPoE as the WAN connection type. Enable VLAN on the WAN interface: VLAN ID 2510, 802.1p priority 0. Enter username fiber and password fiber. Connect the router's WAN port to the CETIN optical converter. Set WAN service type PPPoE over Ethernet. Enable VLAN with 802.1Q VLAN ID 848 and 802.1P priority 0. Set MTU to 1492. Enter PPP username adsl and password adsl.

Before you remove the T-Mobile CZ box

The official page does not settle phone service for a third-party router — confirm before you disconnect the provider box. TV services may use their own VLAN or box; check before swapping. T-Mobile says compatibility cannot be 100% guaranteed and field names vary by router brand. Requirements PDF mentions IPv4/IPv6 support for the ONU; MTU not stated. TV works over the connection with no extra conditions stated. No date on the PDF.

Common setup mistakes

Choose PPPoE, not Dynamic IP — the line will not come up with DHCP alone. Tag the WAN with VLAN 2510; a missing or wrong tag is the most common reason a new router gets no connection. Device must support 802.1q tagging with VLAN 2510, priority 0 Power-cycle the ONT or modem after swapping routers so it releases the old session.

Next step

Evidence

Page reviewed 6 November 2026 · profile researched 6 November 2026.