HHLONIX
EN

South Africa · Afrihost

Can I use my own router with Afrihost?

Yes. Afrihost documents PPPoE with no VLAN tag with your account's broadband login. Check phone and TV services before you remove the provider box.

Network equipment and server rack
Illustrative photograph; equipment and compatibility may differ.Shixart1985 · CC BY 2.0 · Wikimedia Commons
Page reviewed 6 November 2026Profile researched 6 November 2026Cited sources 3How Hlonix verifies →

Quick reference

Own-router settings at a glance

From official provider sources cited below. Pick your router for a full verdict with topology and caveats.

Afrihost Fibre on Openserve / TT Connect / Unifybr / Vodacom — PPPoE

Own-router path
Own router connects directly
Physical handoff
FNO ONT → Ethernet WAN
WAN connection
PPPoE
VLAN
None — untagged
ISP phone / voice
Check with your provider
ISP TV
No dependency documented
Evidence confidence
High — official provider source

Settings to enter on your router

  1. Run an Ethernet cable from ONT port LAN1 to your router's WAN/Internet port.
  2. In ClientZone, open the Connectivity tab, select your fibre package and note the username shown at the top; use Access Details → Reset Password to get a password.
  3. On the router, set the connection type to PPPoE (wired) and enter that username and password.
  4. For IPv6 (Openserve and Vodacom only), set the IPv6 connection type to PPPoE using the same account as IPv4.
  5. Save and allow up to about an hour for activation.

Copy-paste router configuration

Generated from the settings above. Use the broadband username and password from your provider account or welcome email. Menu names vary by firmware version.

OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan'
uci set network.wan.proto='pppoe'
uci set network.wan.username='YOUR_BROADBAND_USERNAME'
uci set network.wan.password='YOUR_BROADBAND_PASSWORD'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restart
MikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/interface pppoe-client add name=pppoe-out1 interface=ether1 user="YOUR_BROADBAND_USERNAME" password="YOUR_BROADBAND_PASSWORD" add-default-route=yes use-peer-dns=yes disabled=no
/interface list member add list=WAN interface=pppoe-out1
UniFi
  1. Settings → Internet → select the WAN (Primary) → Advanced: Manual.
  2. VLAN ID: off.
  3. IPv4 connection: PPPoE — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
  4. Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
  1. Use the physical WAN NIC as WAN.
  2. WAN → IPv4 configuration type: PPPoE, username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
  3. Save, apply, then power-cycle the ONT/modem.
ASUS
  1. WAN → Internet Connection → WAN Connection Type: PPPoE; enter username YOUR_BROADBAND_USERNAME and password YOUR_BROADBAND_PASSWORD.
  2. LAN → IPTV: leave ISP Profile on None.
  3. Apply and reboot the ONT/modem.
TP-Link
  1. Advanced → Network → Internet: connection type PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD).
  2. IPTV/VLAN: leave disabled.
  3. Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
  4. Save and restart the ONT/modem.
FRITZ!Box
  1. Internet → Account Information → Internet service provider: Other Internet service provider.
  2. Connection: external modem or router (LAN 1 as WAN).
  3. Account information required: Yes — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
  4. Use VLAN for internet access: off.
  5. Apply and restart the ONT/modem.
eero / Nest
  1. eero app → Settings → Network settings → ISP settings: PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD).
  2. Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: PPPoE.

Afrihost Fibre on Vumatel — Dynamic IP (DHCP)

Own-router path
Own router connects directly
Physical handoff
Vumatel ONT → Ethernet WAN
WAN connection
DHCP
VLAN
None — untagged
ISP phone / voice
Check with your provider
ISP TV
No dependency documented
Evidence confidence
High — official provider source

Settings to enter on your router

  1. Connect an Ethernet cable from the Vumatel ONT port LAN1 (always LAN1) to your router's WAN/Internet port.
  2. Set the router's internet connection type to Dynamic IP / DHCP; no username or password is needed.
  3. Open the Afrihost activation page and confirm with the one-time PIN sent to the account holder's cell number.
  4. On Vuma Aerial, stay connected only to the fibre network (mobile data off) while activating.

Copy-paste router configuration

Generated from the settings above. Menu names vary by firmware version.

OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan'
uci set network.wan.proto='dhcp'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restart
MikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/ip dhcp-client add interface=ether1 disabled=no
UniFi
  1. Settings → Internet → select the WAN (Primary) → Advanced: Manual.
  2. VLAN ID: off.
  3. IPv4 connection: DHCP.
  4. Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
  1. Use the physical WAN NIC as WAN.
  2. WAN → IPv4 configuration type: DHCP.
  3. Save, apply, then power-cycle the ONT/modem.
ASUS
  1. WAN → Internet Connection → WAN Connection Type: Automatic IP.
  2. LAN → IPTV: leave ISP Profile on None.
  3. Apply and reboot the ONT/modem.
TP-Link
  1. Advanced → Network → Internet: connection type Dynamic IP.
  2. IPTV/VLAN: leave disabled.
  3. Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
  4. Save and restart the ONT/modem.
FRITZ!Box
  1. Internet → Account Information → Internet service provider: Other Internet service provider.
  2. Connection: external modem or router (LAN 1 as WAN).
  3. Account information required: No.
  4. Use VLAN for internet access: off.
  5. Apply and restart the ONT/modem.
eero / Nest
  1. eero app → Settings → Network settings → ISP settings: leave on automatic/DHCP.
  2. Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: DHCP.
WAN authPPPoE
VLANNone — untagged
Priority / PCP—
MTUDefault

What Afrihost officially documents

Run an Ethernet cable from ONT port LAN1 to your router's WAN/Internet port. In ClientZone, open the Connectivity tab, select your fibre package and note the username shown at the top; use Access Details → Reset Password to get a password. On the router, set the connection type to PPPoE (wired) and enter that username and password. For IPv6 (Openserve and Vodacom only), set the IPv6 connection type to PPPoE using the same account as IPv4. Save and allow up to about an hour for activation. Connect an Ethernet cable from the Vumatel ONT port LAN1 (always LAN1) to your router's WAN/Internet port. Set the router's internet connection type to Dynamic IP / DHCP; no username or password is needed. Open the Afrihost activation page and confirm with the one-time PIN sent to the account holder's cell number. On Vuma Aerial, stay connected only to the fibre network (mobile data off) while activating.

Before you remove the Afrihost box

The official page does not settle phone service for a third-party router — confirm before you disconnect the provider box. No TV dependency is documented. Settings depend on the fibre network operator; this profile covers the FNOs Afrihost lists as PPPoE. No VLAN is configured on the router in Afrihost's guides (VLAN, MTU: not stated). Afrihost-supplied routers come preconfigured.

Common setup mistakes

Choose PPPoE, not Dynamic IP — the line will not come up with DHCP alone. Leave WAN VLAN tagging off; adding a tag here breaks the connection. IPv6 on Openserve and Vodacom uses PPPoE with the same account as IPv4. Power-cycle the ONT or modem after swapping routers so it releases the old session.

Next step

Evidence

Page reviewed 6 November 2026 · profile researched 6 November 2026.