South Africa · MWEB
Can I use my own router with MWEB?
Yes. MWEB documents PPPoE with a line-dependent VLAN with your account's broadband login. Check phone and TV services before you remove the provider box.

Quick reference
Own-router settings at a glance
From official provider sources cited below. Pick your router for a full verdict with topology and caveats.
MWEB Fibre — PPPoE (most fibre networks)
- Own-router path
- Own router connects directly (medium-confidence evidence)
- Physical handoff
- FNO ONT → Ethernet WAN
- WAN connection
- PPPoE
- VLAN
- Confirm with provider
- ISP phone / voice
- Check with your provider
- ISP TV
- No dependency documented
- Evidence confidence
- Medium — verify account details
Settings to enter on your router
- Connect the router's WAN port to ONT port LAN1.
- Get your PPP username and password from the SMS MWEB sends, or from My Products → settings cog in your MWEB account.
- Set the WAN connection type to PPPoE and enter the PPP username and password.
- Save and allow up to about 10 minutes for the connection to come up.
Instant verdict for your router:eero 6+Deco X50/X55ASUS RT-AX86U ProArcher BE550Orbi RBK760Nest Wifi ProOther router
MWEB Fibre on Vumatel Active Ethernet — IPoE (DHCP)
- Own-router path
- Own router connects directly (medium-confidence evidence)
- Physical handoff
- Vumatel ONT → Ethernet WAN
- WAN connection
- DHCP
- VLAN
- Confirm with provider
- ISP phone / voice
- Check with your provider
- ISP TV
- No dependency documented
- Evidence confidence
- Medium — verify account details
Settings to enter on your router
- Connect the router's WAN port to ONT port LAN1.
- Set the WAN connection type to IPoE / DHCP (automatic IP); no PPP login fields are needed.
- Save and wait for the router to obtain an address.
Instant verdict for your router:eero 6+Deco X50/X55ASUS RT-AX86U ProArcher BE550Orbi RBK760Nest Wifi ProOther router
Other South African ISPs:AfrihostWebafricaCool IdeasVoxCompare all South African ISP settings
What MWEB officially documents
Connect the router's WAN port to ONT port LAN1. Get your PPP username and password from the SMS MWEB sends, or from My Products → settings cog in your MWEB account. Set the WAN connection type to PPPoE and enter the PPP username and password. Save and allow up to about 10 minutes for the connection to come up. Connect the router's WAN port to ONT port LAN1. Set the WAN connection type to IPoE / DHCP (automatic IP); no PPP login fields are needed. Save and wait for the router to obtain an address.
Before you remove the MWEB box
The official page does not settle phone service for a third-party router — confirm before you disconnect the provider box. No TV dependency is documented. Source is MWEB's manual setup guide for its supplied ZTE router; it labels PPPoE as the setting for most fibre providers. MWEB does not explicitly state an own-router policy. VLAN, MTU, IPv6: not stated.
Common setup mistakes
Choose PPPoE, not Dynamic IP — the line will not come up with DHCP alone. The VLAN depends on the access network behind your line — confirm it with the provider before configuring the router. Power-cycle the ONT or modem after swapping routers so it releases the old session.
Next step
Evidence
- MWEB — ZTE H3601P manual router configuration, fibre setup guide (official) (official ISP)
- MWEB — How to find your settings for any MWEB product (official) (official ISP)
Page reviewed 6 November 2026 · profile researched 6 November 2026.