HHLONIX
EN

Hong Kong · HKBN

Can I use my own router with HKBN?

Yes. HKBN documents DHCP / IPoE with no VLAN tag. Check phone and TV services before you remove the provider box.

Ethernet cable and network connections
Illustrative photograph; equipment and compatibility may differ.Swpb · CC BY-SA 4.0 · Wikimedia Commons
Page reviewed 6 November 2026Profile researched 6 November 2026Cited sources 1How Hlonix verifies →

Quick reference

Own-router settings at a glance

From official provider sources cited below. Pick your router for a full verdict with topology and caveats.

HKBN fibre broadband — own router on DHCP

Own-router path
Own router connects directly
Physical handoff
Wall plate / ONT → Ethernet WAN
WAN connection
DHCP
VLAN
None — untagged
ISP phone / voice
Check with your provider
ISP TV
Check with your provider
Evidence confidence
Medium — verify account details

Settings to enter on your router

  1. Run a network cable from the HKBN wall plate/ONT to the Internet (WAN) port of your router.
  2. In the router's WAN/Internet settings choose automatic configuration (DHCP / Dynamic IP).
  3. No ISP username or password is needed; leave VLAN tagging off.
  4. Save, let the router restart for a few minutes, then confirm it shows a public IPv4 address on its status/diagnostics page.

Copy-paste router configuration

Generated from the settings above. Menu names vary by firmware version.

OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan'
uci set network.wan.proto='dhcp'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restart
MikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/ip dhcp-client add interface=ether1 disabled=no
UniFi
  1. Settings → Internet → select the WAN (Primary) → Advanced: Manual.
  2. VLAN ID: off.
  3. IPv4 connection: DHCP.
  4. Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
  1. Use the physical WAN NIC as WAN.
  2. WAN → IPv4 configuration type: DHCP.
  3. Save, apply, then power-cycle the ONT/modem.
ASUS
  1. WAN → Internet Connection → WAN Connection Type: Automatic IP.
  2. LAN → IPTV: leave ISP Profile on None.
  3. Apply and reboot the ONT/modem.
TP-Link
  1. Advanced → Network → Internet: connection type Dynamic IP.
  2. IPTV/VLAN: leave disabled.
  3. Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
  4. Save and restart the ONT/modem.
FRITZ!Box
  1. Internet → Account Information → Internet service provider: Other Internet service provider.
  2. Connection: external modem or router (LAN 1 as WAN).
  3. Account information required: No.
  4. Use VLAN for internet access: off.
  5. Apply and restart the ONT/modem.
eero / Nest
  1. eero app → Settings → Network settings → ISP settings: leave on automatic/DHCP.
  2. Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: DHCP.
WAN authDHCP / IPoE
VLANNone — untagged
Priority / PCP—
MTUDefault

What HKBN officially documents

Run a network cable from the HKBN wall plate/ONT to the Internet (WAN) port of your router. In the router's WAN/Internet settings choose automatic configuration (DHCP / Dynamic IP). No ISP username or password is needed; leave VLAN tagging off. Save, let the router restart for a few minutes, then confirm it shows a public IPv4 address on its status/diagnostics page.

Before you remove the HKBN box

The official page does not settle phone service for a third-party router — confirm before you disconnect the provider box. TV services may use their own VLAN or box; check before swapping. HKBN publishes step-by-step guides for third-party routers (e.g. Linksys, TOTOLINK, LevelOne); the Linksys guide uses DHCP. VLAN, MTU and MAC cloning not stated. Guide undated (file code suggests 2023). IPv6 not stated.

Common setup mistakes

Choose Dynamic IP / DHCP (IPoE), not PPPoE — there is no broadband login to enter. Leave WAN VLAN tagging off; adding a tag here breaks the connection. Power-cycle the ONT or modem after swapping routers so it releases the old session.

Next step

Evidence

Page reviewed 6 November 2026 · profile researched 6 November 2026.