HHLONIX
EN

Switzerland · Init7

Can I use my own router with Init7 Fiber7?

Yes. Init7 explicitly offers free router choice on Fiber7 and publishes the physical requirements for 1, 10 and 25 Gbit/s tiers. Fiber7 uses DHCP; a media converter can let an Ethernet-only router sit behind the fibre termination.

Ethernet cable and network connections
Illustrative photograph; equipment and compatibility may differ.Santeri Viinamäki · CC BY-SA 4.0 · Wikimedia Commons
Page reviewed 6 November 2026Dataset snapshot 23 September 2026Cited sources 2How Hlonix verifies →

Quick reference

Own-router settings at a glance

From official provider sources cited below. Pick your router for a full verdict with topology and caveats.

Init7 Fiber7 — own router / media converter

Own-router path
Own router connects directly
Physical handoff
Fiber7 fibre or provider media converter → own router
WAN connection
DHCP
VLAN
None — untagged
ISP phone / voice
Check with your provider
ISP TV
Check with your provider
Evidence confidence
High — official provider source

Settings to enter on your router

  1. Use DHCP for Fiber7/Crossover7.
  2. If your router lacks a fibre port, Init7 documents using a media converter with an Ethernet WAN router.
  3. Choose WAN/optics that match the subscribed Fiber7 speed.

Copy-paste router configuration

Generated from the settings above. Menu names vary by firmware version.

OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan'
uci set network.wan.proto='dhcp'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restart
MikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/ip dhcp-client add interface=ether1 disabled=no
UniFi
  1. Settings → Internet → select the WAN (Primary) → Advanced: Manual.
  2. VLAN ID: off.
  3. IPv4 connection: DHCP.
  4. Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
  1. Use the physical WAN NIC as WAN.
  2. WAN → IPv4 configuration type: DHCP.
  3. Save, apply, then power-cycle the ONT/modem.
ASUS
  1. WAN → Internet Connection → WAN Connection Type: Automatic IP.
  2. LAN → IPTV: leave ISP Profile on None.
  3. Apply and reboot the ONT/modem.
TP-Link
  1. Advanced → Network → Internet: connection type Dynamic IP.
  2. IPTV/VLAN: leave disabled.
  3. Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
  4. Save and restart the ONT/modem.
FRITZ!Box
  1. Internet → Account Information → Internet service provider: Other Internet service provider.
  2. Connection: external modem or router (LAN 1 as WAN).
  3. Account information required: No.
  4. Use VLAN for internet access: off.
  5. Apply and restart the ONT/modem.
eero / Nest
  1. eero app → Settings → Network settings → ISP settings: leave on automatic/DHCP.
  2. Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: DHCP.
Router choiceFree choice
Fiber7 1GDHCP
Router lacks fibre portMedia converter supported
10/25GCorrect optics/WAN speed required

Speed tier changes the physical hardware

A 1G router, 10G SFP+ router and 25G SFP28 router are not interchangeable even though the logical WAN method is simple.

Media converter is a useful bridge

Init7 explicitly documents a converter path for customers whose preferred router has Ethernet WAN but no fibre interface.

Do not apply Fiber7 settings to Hybrid7

Init7 Hybrid7 and Copper7 use different VLAN/PPPoE or DSL requirements. This page and checker profile are Fiber7-specific.

Next step

Evidence

Page reviewed 6 November 2026 · compatibility dataset snapshot 23 September 2026.