Japan · NTT FLET'S Hikari
Can I use my own router with NTT FLET'S Hikari?
Yes. NTT FLET'S Hikari documents PPPoE with no VLAN tag with your account's broadband login.
.jpg/960px-Ethernet_Port_(49790583026).jpg)
Quick reference
Own-router settings at a glance
From official provider sources cited below. Pick your router for a full verdict with topology and caveats.
FLET'S Hikari — IPv4 PPPoE with your provider login
- Own-router path
- Own router connects directly (medium-confidence evidence)
- Physical handoff
- ONU (or Hikari Denwa home gateway) → Ethernet WAN
- WAN connection
- PPPoE
- VLAN
- None — untagged
- ISP phone / voice
- Keeps working on the provider hub
- ISP TV
- Check with your provider
- Evidence confidence
- Medium — verify account details
Settings to enter on your router
- Connect the NTT ONU's LAN port to your router's WAN port (if you have Hikari Denwa, either let the NTT home gateway do PPPoE or put your router behind it).
- Choose PPPoE as the WAN connection type.
- Enter the connection username and password issued by your provider (ISP).
- If the NTT home gateway already holds a PPPoE session, stop it there so a session is free for your router.
Copy-paste router configuration
Generated from the settings above. Use the broadband username and password from your provider account or welcome email. Menu names vary by firmware version.
OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan'
uci set network.wan.proto='pppoe'
uci set network.wan.username='YOUR_BROADBAND_USERNAME'
uci set network.wan.password='YOUR_BROADBAND_PASSWORD'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restartMikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/interface pppoe-client add name=pppoe-out1 interface=ether1 user="YOUR_BROADBAND_USERNAME" password="YOUR_BROADBAND_PASSWORD" add-default-route=yes use-peer-dns=yes disabled=no
/interface list member add list=WAN interface=pppoe-out1UniFi
- Settings → Internet → select the WAN (Primary) → Advanced: Manual.
- VLAN ID: off.
- IPv4 connection: PPPoE — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
- Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
- Use the physical WAN NIC as WAN.
- WAN → IPv4 configuration type: PPPoE, username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
- Save, apply, then power-cycle the ONT/modem.
ASUS
- WAN → Internet Connection → WAN Connection Type: PPPoE; enter username YOUR_BROADBAND_USERNAME and password YOUR_BROADBAND_PASSWORD.
- LAN → IPTV: leave ISP Profile on None.
- Apply and reboot the ONT/modem.
TP-Link
- Advanced → Network → Internet: connection type PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD).
- IPTV/VLAN: leave disabled.
- Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
- Save and restart the ONT/modem.
FRITZ!Box
- Internet → Account Information → Internet service provider: Other Internet service provider.
- Connection: external modem or router (LAN 1 as WAN).
- Account information required: Yes — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
- Use VLAN for internet access: off.
- Apply and restart the ONT/modem.
eero / Nest
- eero app → Settings → Network settings → ISP settings: PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD).
- Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: PPPoE.
Instant verdict for your router:eero 6+Deco X50/X55ASUS RT-AX86U ProArcher BE550Orbi RBK760Nest Wifi ProOther router
FLET'S Hikari — IPv6 IPoE (v6 option)
- Own-router path
- Depends on line authentication and router
- Physical handoff
- ONU → Ethernet WAN (IPv6 native)
- WAN connection
- DHCP
- VLAN
- None — untagged
- ISP phone / voice
- Check with your provider
- ISP TV
- Check with your provider
- Evidence confidence
- Medium — verify account details
Settings to enter on your router
- Make sure FLET'S v6 Option is active (or included in your plan) and your ISP supports IPv6 IPoE.
- Connect the ONU (or Hikari Denwa gateway) to your router's WAN port.
- Enable the IPv6/IPoE (or ISP-specific IPv4-over-IPv6) mode on your router; no ID or password is needed for IPv6 IPoE.
- For IPv4 over IPv6, use the method your ISP specifies (see the ISP-specific profiles).
Copy-paste router configuration
Generated from the settings above. Menu names vary by firmware version.
OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan'
uci set network.wan.proto='dhcp'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restartMikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/ip dhcp-client add interface=ether1 disabled=noUniFi
- Settings → Internet → select the WAN (Primary) → Advanced: Manual.
- VLAN ID: off.
- IPv4 connection: DHCP.
- Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
- Use the physical WAN NIC as WAN.
- WAN → IPv4 configuration type: DHCP.
- Save, apply, then power-cycle the ONT/modem.
ASUS
- WAN → Internet Connection → WAN Connection Type: Automatic IP.
- LAN → IPTV: leave ISP Profile on None.
- Apply and reboot the ONT/modem.
TP-Link
- Advanced → Network → Internet: connection type Dynamic IP.
- IPTV/VLAN: leave disabled.
- Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
- Save and restart the ONT/modem.
FRITZ!Box
- Internet → Account Information → Internet service provider: Other Internet service provider.
- Connection: external modem or router (LAN 1 as WAN).
- Account information required: No.
- Use VLAN for internet access: off.
- Apply and restart the ONT/modem.
eero / Nest
- eero app → Settings → Network settings → ISP settings: leave on automatic/DHCP.
- Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: DHCP.
Instant verdict for your router:eero 6+Deco X50/X55ASUS RT-AX86U ProArcher BE550Orbi RBK760Nest Wifi ProOther router
Other Japanese ISPs:So-netBIGLOBEau Hikari (KDDI)NURO HikariCompare all Japanese ISP settings
What NTT FLET'S Hikari officially documents
Connect the NTT ONU's LAN port to your router's WAN port (if you have Hikari Denwa, either let the NTT home gateway do PPPoE or put your router behind it). Choose PPPoE as the WAN connection type. Enter the connection username and password issued by your provider (ISP). If the NTT home gateway already holds a PPPoE session, stop it there so a session is free for your router. Make sure FLET'S v6 Option is active (or included in your plan) and your ISP supports IPv6 IPoE. Connect the ONU (or Hikari Denwa gateway) to your router's WAN port. Enable the IPv6/IPoE (or ISP-specific IPv4-over-IPv6) mode on your router; no ID or password is needed for IPv6 IPoE. For IPv4 over IPv6, use the method your ISP specifies (see the ISP-specific profiles).
Before you remove the NTT FLET'S Hikari box
Phone service keeps working on the provider device. TV services may use their own VLAN or box; check before swapping. NTT documents PPPoE with provider-issued credentials on its home gateways and notes disconnecting sessions to free them up; session limits, MTU and passthrough are not stated. FLET'S is a wholesale line: the ISP (OCN, So-net, BIGLOBE, etc.) supplies the PPPoE login. See the IPoE profile for IPv6.
Common setup mistakes
Choose PPPoE, not Dynamic IP — the line will not come up with DHCP alone. Leave WAN VLAN tagging off; adding a tag here breaks the connection. Credentials are issued by your ISP (provider), not by NTT Power-cycle the ONT or modem after swapping routers so it releases the old session.
Next step
Evidence
- NTT East — RX-600KI home gateway PPPoE setup notice (official PDF) (official ISP)
- NTT East — FLET'S Hikari Next IPv6 (IPoE vs PPPoE) (official) (official ISP)
Page reviewed 6 November 2026 · profile researched 6 November 2026.