HHLONIX
EN

Netherlands · Budget Thuis

Can I use my own router with Budget Thuis?

Yes. Budget Thuis documents DHCP / IPoE with no VLAN tag. Check phone and TV services before you remove the provider box.

Ethernet cable and network connections
Illustrative photograph; equipment and compatibility may differ.Marcnovac · CC BY-SA 4.0 · Wikimedia Commons
Page reviewed 6 November 2026Profile researched 6 November 2026Cited sources 2How Hlonix verifies →

Quick reference

Own-router settings at a glance

From official provider sources cited below. Pick your router for a full verdict with topology and caveats.

Budget Thuis Glasvezel — own router via the NT, plain DHCP

Own-router path
Own router connects directly
Physical handoff
Fibre NT → Ethernet WAN
WAN connection
DHCP
VLAN
None — untagged
ISP phone / voice
Check with your provider
ISP TV
Check with your provider
Evidence confidence
Medium — verify account details

Settings to enter on your router

  1. Connect your router's WAN port to the Budget Thuis (O)NT with a network cable. Do not connect it straight to the fibre.
  2. Set WAN to DHCP client (automatic IP). It receives the IP address and DNS servers by itself.
  3. Leave VLAN tagging off. The guide says no extra VLAN settings are needed.

Copy-paste router configuration

Generated from the settings above. Menu names vary by firmware version.

OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan'
uci set network.wan.proto='dhcp'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restart
MikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/ip dhcp-client add interface=ether1 disabled=no
UniFi
  1. Settings → Internet → select the WAN (Primary) → Advanced: Manual.
  2. VLAN ID: off.
  3. IPv4 connection: DHCP.
  4. Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
  1. Use the physical WAN NIC as WAN.
  2. WAN → IPv4 configuration type: DHCP.
  3. Save, apply, then power-cycle the ONT/modem.
ASUS
  1. WAN → Internet Connection → WAN Connection Type: Automatic IP.
  2. LAN → IPTV: leave ISP Profile on None.
  3. Apply and reboot the ONT/modem.
TP-Link
  1. Advanced → Network → Internet: connection type Dynamic IP.
  2. IPTV/VLAN: leave disabled.
  3. Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
  4. Save and restart the ONT/modem.
FRITZ!Box
  1. Internet → Account Information → Internet service provider: Other Internet service provider.
  2. Connection: external modem or router (LAN 1 as WAN).
  3. Account information required: No.
  4. Use VLAN for internet access: off.
  5. Apply and restart the ONT/modem.
eero / Nest
  1. eero app → Settings → Network settings → ISP settings: leave on automatic/DHCP.
  2. Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: DHCP.

Budget Thuis DSL (VDSL) — own modem, PPPoE on VLAN 6

Own-router path
Own router connects directly
Physical handoff
VDSL line → own VDSL modem-router
WAN connection
PPPoE
VLAN
VLAN 6 (802.1Q tagged)
ISP phone / voice
Check with your provider
ISP TV
Check with your provider
Evidence confidence
High — official provider source

Settings to enter on your router

  1. Check your line type in the Budget modem first (VDSL, vectoring, bonding), and use a modem that supports it.
  2. Create a PPPoE internet connection on 802.1Q VLAN 6 with PAP, using the username and password supplied by Budget Thuis. Set MTU to 1500.
  3. Turn on IPv6 and request a prefix by DHCPv6-PD over the PPP link.
  4. For TV, add a routed VLAN 4 interface. Its DHCP client sends option 60 'IPTV_RG' and requests options 1, 3, 28 and 121. Use only the routes it receives, and turn on IGMP proxy (v2, fast leave) and IGMP snooping.
  5. For telephony, register SIP over VLAN 6 using your phone number and the VoIP username and password from MijnBudget.

Copy-paste router configuration

Generated from the settings above. Use the broadband username and password from your provider account or welcome email. Menu names vary by firmware version.

UniFi
  1. Settings → Internet → select the WAN (Primary) → Advanced: Manual.
  2. VLAN ID: on, 6.
  3. IPv4 connection: PPPoE — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
  4. Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
  1. Interfaces → VLANs (OPNsense: Interfaces → Other Types → VLAN): parent = WAN NIC, tag 6, priority 0.
  2. Interfaces → Assignments: assign the new VLAN as WAN.
  3. WAN → IPv4 configuration type: PPPoE, username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
  4. Save, apply, then power-cycle the ONT/modem.
ASUS
  1. WAN → Internet Connection → WAN Connection Type: PPPoE; enter username YOUR_BROADBAND_USERNAME and password YOUR_BROADBAND_PASSWORD.
  2. LAN → IPTV → Select ISP Profile: Manual → Internet: VID 6, PRIO 0.
  3. Apply and reboot the ONT/modem.
TP-Link
  1. Advanced → Network → Internet: connection type PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD).
  2. Advanced → Network → IPTV/VLAN: enable, Mode Custom, Internet VLAN ID 6.
  3. Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
  4. Save and restart the ONT/modem.
FRITZ!Box
  1. Internet → Account Information → Internet service provider: Other Internet service provider.
  2. Connection: via DSL (VDSL).
  3. Account information required: Yes — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
  4. Use VLAN for internet access: on, VLAN ID 6.
  5. Apply and restart the ONT/modem.
eero / Nest
  1. eero app → Settings → Network settings → ISP settings: PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD); VLAN ID 6.
  2. Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: PPPoE; VLAN 6 where your firmware offers it.
WAN authDHCP / IPoE
VLANNone — untagged
Priority / PCP—
MTUDefault

What Budget Thuis officially documents

Connect your router's WAN port to the Budget Thuis (O)NT with a network cable. Do not connect it straight to the fibre. Set WAN to DHCP client (automatic IP). It receives the IP address and DNS servers by itself. Leave VLAN tagging off. The guide says no extra VLAN settings are needed. Check your line type in the Budget modem first (VDSL, vectoring, bonding), and use a modem that supports it. Create a PPPoE internet connection on 802.1Q VLAN 6 with PAP, using the username and password supplied by Budget Thuis. Set MTU to 1500. Turn on IPv6 and request a prefix by DHCPv6-PD over the PPP link. For TV, add a routed VLAN 4 interface. Its DHCP client sends option 60 'IPTV_RG' and requests options 1, 3, 28 and 121. Use only the routes it receives, and turn on IGMP proxy (v2, fast leave) and IGMP snooping. For telephony, register SIP over VLAN 6 using your phone number and the VoIP username and password from MijnBudget.

Before you remove the Budget Thuis box

The official page does not settle phone service for a third-party router — confirm before you disconnect the provider box. TV services may use their own VLAN or box; check before swapping. Short official PDF with no date. MTU, IPv6, telephony and TV settings are not stated.

Common setup mistakes

Choose Dynamic IP / DHCP (IPoE), not PPPoE — there is no broadband login to enter. Leave WAN VLAN tagging off; adding a tag here breaks the connection. Power-cycle the ONT or modem after swapping routers so it releases the old session.

Next step

Evidence

Page reviewed 6 November 2026 · profile researched 6 November 2026.