HHLONIX
EN

Singapore · StarHub

Can I use my own router with StarHub Fibre?

On an ONT-based StarHub setup, yes: StarHub's current guide describes the ONT as the fibre termination device and the separate router as user-replaceable networking hardware. ONR-based setups need a different bridge/AP decision.

Fibre-optic broadband infrastructure
Illustrative photograph; equipment and compatibility may differ.Profpcde · CC0 1.0 · Wikimedia Commons
Page reviewed 6 November 2026Dataset snapshot 23 September 2026Cited sources 1How Hlonix verifies →

Quick reference

Own-router settings at a glance

From official provider sources cited below. Pick your router for a full verdict with topology and caveats.

StarHub Fibre — ONT + own router

Own-router path
Own router connects directly (medium-confidence evidence)
Physical handoff
StarHub ONT → Ethernet WAN router
WAN connection
DHCP
VLAN
None — untagged
ISP phone / voice
Check with your provider
ISP TV
Check with your provider
Evidence confidence
Medium — verify account details

Settings to enter on your router

  1. Use a separate router behind the StarHub ONT.
  2. StarHub's current ONT guide describes ONT + router as the flexible setup where the router can be swapped independently.
  3. Verify plan-specific WAN settings if your account uses a non-standard managed service.

Copy-paste router configuration

Generated from the settings above. Menu names vary by firmware version.

OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan'
uci set network.wan.proto='dhcp'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restart
MikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/ip dhcp-client add interface=ether1 disabled=no
UniFi
  1. Settings → Internet → select the WAN (Primary) → Advanced: Manual.
  2. VLAN ID: off.
  3. IPv4 connection: DHCP.
  4. Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
  1. Use the physical WAN NIC as WAN.
  2. WAN → IPv4 configuration type: DHCP.
  3. Save, apply, then power-cycle the ONT/modem.
ASUS
  1. WAN → Internet Connection → WAN Connection Type: Automatic IP.
  2. LAN → IPTV: leave ISP Profile on None.
  3. Apply and reboot the ONT/modem.
TP-Link
  1. Advanced → Network → Internet: connection type Dynamic IP.
  2. IPTV/VLAN: leave disabled.
  3. Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
  4. Save and restart the ONT/modem.
FRITZ!Box
  1. Internet → Account Information → Internet service provider: Other Internet service provider.
  2. Connection: external modem or router (LAN 1 as WAN).
  3. Account information required: No.
  4. Use VLAN for internet access: off.
  5. Apply and restart the ONT/modem.
eero / Nest
  1. eero app → Settings → Network settings → ISP settings: leave on automatic/DHCP.
  2. Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: DHCP.
ONT setupSeparate router required
Router choiceFlexible on ONT topology
ONR setupBridge/AP considerations
Multi-gigPort speed matters

Identify ONT vs ONR first

An ONT does not route or provide Wi-Fi; an ONR combines both functions. The same third-party router therefore has a different role depending on which device StarHub installed.

ONT is the cleaner own-router case

The router plugs into the ONT via Ethernet and can be upgraded independently without changing the fibre termination.

ONR may need bridge or AP mode

StarHub notes that using your own router with an ONR requires bridge mode if supported, or AP mode on the added router to avoid double NAT.

Next step

Evidence

Page reviewed 6 November 2026 · compatibility dataset snapshot 23 September 2026.