HHLONIX
EN

Germany · M-net

Can I use my own router with M-net?

Yes. M-net documents PPPoE on VLAN 40 with your account's broadband login. Check phone and TV services before you remove the provider box.

Ethernet cable and network connections
Illustrative photograph; equipment and compatibility may differ.Swpb · CC BY-SA 4.0 · Wikimedia Commons
Page reviewed 6 November 2026Profile researched 6 November 2026Cited sources 2How Hlonix verifies →

Quick reference

Own-router settings at a glance

From official provider sources cited below. Pick your router for a full verdict with topology and caveats.

M-net Glasfaser — own router or ONT allowed (PPPoE, VLAN 40)

Own-router path
Own router connects directly (medium-confidence evidence)
Physical handoff
Fibre ONT / FTTB → Ethernet WAN (PPPoE)
WAN connection
PPPoE
VLAN
VLAN 40 (802.1Q tagged)
ISP phone / voice
Check with your provider
ISP TV
Check with your provider
Evidence confidence
Medium — verify account details

Settings to enter on your router

  1. Connect your router's WAN port to the M-net ONT's RJ45 port (or use your own ONT — M-net allows both).
  2. Enable VLAN tagging on WAN with VLAN ID 40.
  3. Select PPPoE and enter the PPP username and password from the M-net customer portal or your welcome letter.
  4. Enable IPv6: tariffs up to 500 Mbit/s use DS-Lite (IPv4 via NAT gateway); 1000 Mbit/s and above get dual stack with a public IPv4.
  5. For telephony, add the SIP accounts — your router must support SIP.

Copy-paste router configuration

Generated from the settings above. Use the broadband username and password from your provider account or welcome email. Menu names vary by firmware version.

OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan.40'
uci set network.wan.proto='pppoe'
uci set network.wan.username='YOUR_BROADBAND_USERNAME'
uci set network.wan.password='YOUR_BROADBAND_PASSWORD'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restart
MikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/interface vlan add name=wan-vlan40 vlan-id=40 interface=ether1
/interface pppoe-client add name=pppoe-out1 interface=wan-vlan40 user="YOUR_BROADBAND_USERNAME" password="YOUR_BROADBAND_PASSWORD" add-default-route=yes use-peer-dns=yes disabled=no
/interface list member add list=WAN interface=pppoe-out1
UniFi
  1. Settings → Internet → select the WAN (Primary) → Advanced: Manual.
  2. VLAN ID: on, 40.
  3. IPv4 connection: PPPoE — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
  4. Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
  1. Interfaces → VLANs (OPNsense: Interfaces → Other Types → VLAN): parent = WAN NIC, tag 40, priority 0.
  2. Interfaces → Assignments: assign the new VLAN as WAN.
  3. WAN → IPv4 configuration type: PPPoE, username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
  4. Save, apply, then power-cycle the ONT/modem.
ASUS
  1. WAN → Internet Connection → WAN Connection Type: PPPoE; enter username YOUR_BROADBAND_USERNAME and password YOUR_BROADBAND_PASSWORD.
  2. LAN → IPTV → Select ISP Profile: Manual → Internet: VID 40, PRIO 0.
  3. Apply and reboot the ONT/modem.
TP-Link
  1. Advanced → Network → Internet: connection type PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD).
  2. Advanced → Network → IPTV/VLAN: enable, Mode Custom, Internet VLAN ID 40.
  3. Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
  4. Save and restart the ONT/modem.
FRITZ!Box
  1. Internet → Account Information → Internet service provider: Other Internet service provider.
  2. Connection: external modem or router (LAN 1 as WAN).
  3. Account information required: Yes — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
  4. Use VLAN for internet access: on, VLAN ID 40.
  5. Apply and restart the ONT/modem.
eero / Nest
  1. eero app → Settings → Network settings → ISP settings: PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD); VLAN ID 40.
  2. Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: PPPoE; VLAN 40 where your firmware offers it.
WAN authPPPoE
VLAN40 (802.1Q tagged)
Priority / PCPNot stated
MTUDefault

What M-net officially documents

Connect your router's WAN port to the M-net ONT's RJ45 port (or use your own ONT — M-net allows both). Enable VLAN tagging on WAN with VLAN ID 40. Select PPPoE and enter the PPP username and password from the M-net customer portal or your welcome letter. Enable IPv6: tariffs up to 500 Mbit/s use DS-Lite (IPv4 via NAT gateway); 1000 Mbit/s and above get dual stack with a public IPv4. For telephony, add the SIP accounts — your router must support SIP.

Before you remove the M-net box

The official page does not settle phone service for a third-party router — confirm before you disconnect the provider box. TV services may use their own VLAN or box; check before swapping. Own router/ONT explicitly allowed per Leistungsbeschreibung (Stand Oktober 2026). VLAN 40/PPPoE come from the M-net 'Premium' interface spec V1.2 (17.07.2020); confirm it applies to your residential product. MTU and SIP registrar not stated. VDSL/G.fast lines use the same VLAN 40 per the spec.

Common setup mistakes

Choose PPPoE, not Dynamic IP — the line will not come up with DHCP alone. Tag the WAN with VLAN 40; a missing or wrong tag is the most common reason a new router gets no connection. VLAN 40 for data and PPPoE (PAP/CHAP) are from the Premium-product interface spec (2020). Voice on Premium IP TKA uses VLAN 200 with 802.1p priority 5. Power-cycle the ONT or modem after swapping routers so it releases the old session.

Next step

Evidence

Page reviewed 6 November 2026 · profile researched 6 November 2026.