HHLONIX
EN

Italy · TIM

Can I use my own router with TIM?

Yes. TIM documents PPPoE on VLAN 835 with your account's broadband login. Check phone and TV services before you remove the provider box.

Network equipment and server rack
Illustrative photograph; equipment and compatibility may differ.Shixart1985 · CC BY 2.0 · Wikimedia Commons
Page reviewed 6 November 2026Profile researched 6 November 2026Cited sources 1How Hlonix verifies →

Quick reference

Own-router settings at a glance

From official provider sources cited below. Pick your router for a full verdict with topology and caveats.

TIM Fibra FTTH — own router via TIM ONT

Own-router path
Own router connects directly
Physical handoff
Fibre ONT → Ethernet WAN
WAN connection
PPPoE
VLAN
VLAN 835 (802.1Q tagged)
ISP phone / voice
Check with your provider
ISP TV
Check with your provider
Evidence confidence
High — official provider source

Settings to enter on your router

  1. Plug the router's WAN port into the LAN port of the TIM-supplied ONT with a Cat 5e or better cable.
  2. Set the WAN connection type to PPPoE (routed) with NAT enabled.
  3. Enable 802.1Q tagging on the WAN with VLAN ID 835.
  4. Enter your landline phone number as the PPPoE username and timadsl as the password.
  5. Optional, for TIM Video Live multicast: add a second WAN on VLAN 836 with static IP 10.10.10.2 / 255.255.255.252, IGMP proxy v2, and enable IGMP snooping on the LAN.

Copy-paste router configuration

Generated from the settings above. Replace the username placeholder with your own value; the password is the generic one the provider publishes. Menu names vary by firmware version.

OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan.835'
uci set network.wan.proto='pppoe'
uci set network.wan.username='YOUR_LANDLINE_NUMBER'
uci set network.wan.password='timadsl'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restart
MikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/interface vlan add name=wan-vlan835 vlan-id=835 interface=ether1
/interface pppoe-client add name=pppoe-out1 interface=wan-vlan835 user="YOUR_LANDLINE_NUMBER" password="timadsl" add-default-route=yes use-peer-dns=yes disabled=no
/interface list member add list=WAN interface=pppoe-out1
UniFi
  1. Settings → Internet → select the WAN (Primary) → Advanced: Manual.
  2. VLAN ID: on, 835.
  3. IPv4 connection: PPPoE — username YOUR_LANDLINE_NUMBER, password timadsl.
  4. Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
  1. Interfaces → VLANs (OPNsense: Interfaces → Other Types → VLAN): parent = WAN NIC, tag 835, priority 0.
  2. Interfaces → Assignments: assign the new VLAN as WAN.
  3. WAN → IPv4 configuration type: PPPoE, username YOUR_LANDLINE_NUMBER, password timadsl.
  4. Save, apply, then power-cycle the ONT/modem.
ASUS
  1. WAN → Internet Connection → WAN Connection Type: PPPoE; enter username YOUR_LANDLINE_NUMBER and password timadsl.
  2. LAN → IPTV → Select ISP Profile: Manual → Internet: VID 835, PRIO 0.
  3. Apply and reboot the ONT/modem.
TP-Link
  1. Advanced → Network → Internet: connection type PPPoE (username YOUR_LANDLINE_NUMBER, password timadsl).
  2. Advanced → Network → IPTV/VLAN: enable, Mode Custom, Internet VLAN ID 835.
  3. Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
  4. Save and restart the ONT/modem.
FRITZ!Box
  1. Internet → Account Information → Internet service provider: Other Internet service provider.
  2. Connection: external modem or router (LAN 1 as WAN).
  3. Account information required: Yes — username YOUR_LANDLINE_NUMBER, password timadsl.
  4. Use VLAN for internet access: on, VLAN ID 835.
  5. Apply and restart the ONT/modem.
eero / Nest
  1. eero app → Settings → Network settings → ISP settings: PPPoE (username YOUR_LANDLINE_NUMBER, password timadsl); VLAN ID 835.
  2. Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: PPPoE; VLAN 835 where your firmware offers it.
WAN authPPPoE
VLAN835 (802.1Q tagged)
Priority / PCPNot stated
MTUDefault

What TIM officially documents

Plug the router's WAN port into the LAN port of the TIM-supplied ONT with a Cat 5e or better cable. Set the WAN connection type to PPPoE (routed) with NAT enabled. Enable 802.1Q tagging on the WAN with VLAN ID 835. Enter your landline phone number as the PPPoE username and timadsl as the password. Optional, for TIM Video Live multicast: add a second WAN on VLAN 836 with static IP 10.10.10.2 / 255.255.255.252, IGMP proxy v2, and enable IGMP snooping on the LAN.

Before you remove the TIM box

The official page does not settle phone service for a third-party router — confirm before you disconnect the provider box. TV services may use their own VLAN or box; check before swapping. MTU and 802.1p priority not stated. VoIP uses SIP domain telecomitalia.it (UDP 5060); per-line SIP credentials and outbound proxy are obtained from TIM (187 / Angie), not listed on the page. FTTC uses the same PPPoE credentials over VDSL2 PTM with VLAN 835. Page shows no update date.

Common setup mistakes

Choose PPPoE, not Dynamic IP — the line will not come up with DHCP alone. Tag the WAN with VLAN 835; a missing or wrong tag is the most common reason a new router gets no connection. Username is the customer's landline phone number; password is the generic value timadsl. Optional IPTV/multicast connection: static IPoE on VLAN 836 (10.10.10.2/30) with IGMP proxy v2. Power-cycle the ONT or modem after swapping routers so it releases the old session.

Next step

Evidence

Page reviewed 6 November 2026 · profile researched 6 November 2026.