HHLONIX
EN

Italy · WindTre

Can I use my own router with WindTre?

Yes. WindTre documents PPPoE on VLAN 835 and generic login values. Check phone and TV services before you remove the provider box.

Ethernet cable and network connections
Illustrative photograph; equipment and compatibility may differ.Swpb · CC BY-SA 4.0 · Wikimedia Commons
Page reviewed 6 November 2026Profile researched 6 November 2026Cited sources 1How Hlonix verifies →

Quick reference

Own-router settings at a glance

From official provider sources cited below. Pick your router for a full verdict with topology and caveats.

WINDTRE Fibra FTTH — own router

Own-router path
Own router connects directly
Physical handoff
Fibre ONT (or SFP ONT module) → Ethernet WAN
WAN connection
PPPoE
VLAN
VLAN 835 (802.1Q tagged)
ISP phone / voice
Check with your provider
ISP TV
No dependency documented
Evidence confidence
High — official provider source

Settings to enter on your router

  1. Connect the router to the fibre via an ONT, or an SFP module in a router with an SFP port (WINDTRE supplies a compatible SFP free if needed).
  2. Set WAN type to PPPoE with NAT enabled.
  3. Set data VLAN ID 835 with 802.1p priority 0.
  4. Enter username benvenuto and password ospite.
  5. For VoIP on FTTH, use VLAN 836 with priority 5 and SIP credentials requested from customer service (159).

Copy-paste router configuration

Generated from the settings above. Generic values published by the provider — any non-empty value is accepted where the provider says so. Menu names vary by firmware version.

OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan.835'
uci set network.wan.proto='pppoe'
uci set network.wan.username='benvenuto'
uci set network.wan.password='ospite'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restart
MikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/interface vlan add name=wan-vlan835 vlan-id=835 interface=ether1
/interface pppoe-client add name=pppoe-out1 interface=wan-vlan835 user="benvenuto" password="ospite" add-default-route=yes use-peer-dns=yes disabled=no
/interface list member add list=WAN interface=pppoe-out1
UniFi
  1. Settings → Internet → select the WAN (Primary) → Advanced: Manual.
  2. VLAN ID: on, 835.
  3. IPv4 connection: PPPoE — username benvenuto, password ospite.
  4. Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
  1. Interfaces → VLANs (OPNsense: Interfaces → Other Types → VLAN): parent = WAN NIC, tag 835, priority 0.
  2. Interfaces → Assignments: assign the new VLAN as WAN.
  3. WAN → IPv4 configuration type: PPPoE, username benvenuto, password ospite.
  4. Save, apply, then power-cycle the ONT/modem.
ASUS
  1. WAN → Internet Connection → WAN Connection Type: PPPoE; enter username benvenuto and password ospite.
  2. LAN → IPTV → Select ISP Profile: Manual → Internet: VID 835, PRIO 0.
  3. Apply and reboot the ONT/modem.
TP-Link
  1. Advanced → Network → Internet: connection type PPPoE (username benvenuto, password ospite).
  2. Advanced → Network → IPTV/VLAN: enable, Mode Custom, Internet VLAN ID 835.
  3. Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
  4. Save and restart the ONT/modem.
FRITZ!Box
  1. Internet → Account Information → Internet service provider: Other Internet service provider.
  2. Connection: external modem or router (LAN 1 as WAN).
  3. Account information required: Yes — username benvenuto, password ospite.
  4. Use VLAN for internet access: on, VLAN ID 835.
  5. Apply and restart the ONT/modem.
eero / Nest
  1. eero app → Settings → Network settings → ISP settings: PPPoE (username benvenuto, password ospite); VLAN ID 835.
  2. Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: PPPoE; VLAN 835 where your firmware offers it.
WAN authPPPoE
VLAN835 (802.1Q tagged)
Priority / PCP0
MTUDefault

What WindTre officially documents

Connect the router to the fibre via an ONT, or an SFP module in a router with an SFP port (WINDTRE supplies a compatible SFP free if needed). Set WAN type to PPPoE with NAT enabled. Set data VLAN ID 835 with 802.1p priority 0. Enter username benvenuto and password ospite. For VoIP on FTTH, use VLAN 836 with priority 5 and SIP credentials requested from customer service (159).

Before you remove the WindTre box

The official page does not settle phone service for a third-party router — confirm before you disconnect the provider box. No TV dependency is documented. MTU not stated for FTTH (FTTC listed with MTU 1492, VLAN 835, same generic credentials). IPv6 not stated. VoIP credentials only on request via 159.

Common setup mistakes

Choose PPPoE, not Dynamic IP — the line will not come up with DHCP alone. Tag the WAN with VLAN 835; a missing or wrong tag is the most common reason a new router gets no connection. Voice VLAN 836 with 802.1p CoS 5. Power-cycle the ONT or modem after swapping routers so it releases the old session.

Next step

Evidence

Page reviewed 6 November 2026 · profile researched 6 November 2026.