HHLONIX
EN

New Zealand · Contact Energy

Can I use my own router with Contact Energy?

Yes. Contact Energy documents DHCP / IPoE on VLAN 10. Phone service needs the provider device.

Network equipment and server rack
Illustrative photograph; equipment and compatibility may differ.Shixart1985 · CC BY 2.0 · Wikimedia Commons
Page reviewed 6 November 2026Profile researched 6 November 2026Cited sources 1How Hlonix verifies →

Quick reference

Own-router settings at a glance

From official provider sources cited below. Pick your router for a full verdict with topology and caveats.

Contact Energy Broadband UFB Fibre — own router

Own-router path
Own router connects directly
Physical handoff
Fibre ONT → Ethernet WAN
WAN connection
DHCP
VLAN
VLAN 10 (802.1Q tagged)
ISP phone / voice
Provider hub required
ISP TV
Check with your provider
Evidence confidence
High — official provider source

Settings to enter on your router

  1. Connect the router's Ethernet WAN port to the ONT and set the operating mode to Ethernet WAN.
  2. Set the connection type to Dynamic IP / IPoE / DHCP.
  3. Enable 802.1q VLAN with ID 10 and 802.1p priority 0.
  4. Set MTU to 1500 (1492 also accepted) and keep NAT enabled.

Copy-paste router configuration

Generated from the settings above. Menu names vary by firmware version.

OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan.10'
uci set network.wan.proto='dhcp'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restart
MikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/interface vlan add name=wan-vlan10 vlan-id=10 interface=ether1
/ip dhcp-client add interface=wan-vlan10 disabled=no
/interface list member add list=WAN interface=wan-vlan10
UniFi
  1. Settings → Internet → select the WAN (Primary) → Advanced: Manual.
  2. VLAN ID: on, 10.
  3. IPv4 connection: DHCP.
  4. Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
  1. Interfaces → VLANs (OPNsense: Interfaces → Other Types → VLAN): parent = WAN NIC, tag 10, priority 0.
  2. Interfaces → Assignments: assign the new VLAN as WAN.
  3. WAN → IPv4 configuration type: DHCP.
  4. Save, apply, then power-cycle the ONT/modem.
ASUS
  1. WAN → Internet Connection → WAN Connection Type: Automatic IP.
  2. LAN → IPTV → Select ISP Profile: Manual → Internet: VID 10, PRIO 0.
  3. Apply and reboot the ONT/modem.
TP-Link
  1. Advanced → Network → Internet: connection type Dynamic IP.
  2. Advanced → Network → IPTV/VLAN: enable, Mode Custom, Internet VLAN ID 10.
  3. Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
  4. Save and restart the ONT/modem.
FRITZ!Box
  1. Internet → Account Information → Internet service provider: Other Internet service provider.
  2. Connection: external modem or router (LAN 1 as WAN).
  3. Account information required: No.
  4. Use VLAN for internet access: on, VLAN ID 10.
  5. Apply and restart the ONT/modem.
eero / Nest
  1. eero app → Settings → Network settings → ISP settings: leave on automatic/DHCP; VLAN ID 10.
  2. Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: DHCP; VLAN 10 where your firmware offers it.
WAN authDHCP / IPoE
VLAN10 (802.1Q tagged)
Priority / PCP0
MTU1500

What Contact Energy officially documents

Connect the router's Ethernet WAN port to the ONT and set the operating mode to Ethernet WAN. Set the connection type to Dynamic IP / IPoE / DHCP. Enable 802.1q VLAN with ID 10 and 802.1p priority 0. Set MTU to 1500 (1492 also accepted) and keep NAT enabled.

Before you remove the Contact Energy box

Phone service on this connection depends on the provider device. TV services may use their own VLAN or box; check before swapping. No PPPoE login listed. Home phone (VoIP) requires a Contact-supplied modem. IPv6 not stated. No page date (footer © 2026).

Common setup mistakes

Choose Dynamic IP / DHCP (IPoE), not PPPoE — there is no broadband login to enter. Tag the WAN with VLAN 10; a missing or wrong tag is the most common reason a new router gets no connection. MTU 1492 or 1500; NAT on (full cone) Power-cycle the ONT or modem after swapping routers so it releases the old session.

Next step

Evidence

Page reviewed 6 November 2026 · profile researched 6 November 2026.