HHLONIX
EN

New Zealand · Spark

Can I use my own router with Spark Fibre?

Yes. Spark publishes detailed third-party Fibre settings: PPPoE, 802.1Q VLAN 10, PCP 0 and a non-empty PPP username/password. The router connects by Ethernet to the Fibre ONT.

Fibre-optic broadband infrastructure
Illustrative photograph; equipment and compatibility may differ.Profpcde · CC0 1.0 · Wikimedia Commons
Page reviewed 6 November 2026Dataset snapshot 23 September 2026Cited sources 1How Hlonix verifies →

Quick reference

Own-router settings at a glance

From official provider sources cited below. Pick your router for a full verdict with topology and caveats.

Spark Fibre — BYO router via ONT

Own-router path
Own router connects directly
Physical handoff
Fibre ONT → Ethernet WAN
WAN connection
PPPoE
VLAN
VLAN 10 (802.1Q tagged)
ISP phone / voice
Check with your provider
ISP TV
No dependency documented
Evidence confidence
High — official provider source

Settings to enter on your router

  1. Use PPPoE.
  2. Use any non-empty PPP username/password; Spark documents user@spark.co.nz / password as examples.
  3. Enable 802.1Q VLAN tagging with VLAN ID 10 and PCP 0.
  4. Use MTU Auto or 1500.

Copy-paste router configuration

Generated from the settings above. Generic values published by the provider — any non-empty value is accepted where the provider says so. Menu names vary by firmware version.

OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan.10'
uci set network.wan.proto='pppoe'
uci set network.wan.username='user@spark.co.nz'
uci set network.wan.password='password'
# Provider lists MTU 1500: only set mtu 1500 if your hardware supports RFC 4638 baby jumbo frames.
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restart
MikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/interface vlan add name=wan-vlan10 vlan-id=10 interface=ether1
/interface pppoe-client add name=pppoe-out1 interface=wan-vlan10 user="user@spark.co.nz" password="password" add-default-route=yes use-peer-dns=yes disabled=no
/interface list member add list=WAN interface=pppoe-out1
UniFi
  1. Settings → Internet → select the WAN (Primary) → Advanced: Manual.
  2. VLAN ID: on, 10.
  3. IPv4 connection: PPPoE — username user@spark.co.nz, password password.
  4. Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
  1. Interfaces → VLANs (OPNsense: Interfaces → Other Types → VLAN): parent = WAN NIC, tag 10, priority 0.
  2. Interfaces → Assignments: assign the new VLAN as WAN.
  3. WAN → IPv4 configuration type: PPPoE, username user@spark.co.nz, password password.
  4. Save, apply, then power-cycle the ONT/modem.
ASUS
  1. WAN → Internet Connection → WAN Connection Type: PPPoE; enter username user@spark.co.nz and password password.
  2. LAN → IPTV → Select ISP Profile: Manual → Internet: VID 10, PRIO 0.
  3. Apply and reboot the ONT/modem.
TP-Link
  1. Advanced → Network → Internet: connection type PPPoE (username user@spark.co.nz, password password).
  2. Advanced → Network → IPTV/VLAN: enable, Mode Custom, Internet VLAN ID 10.
  3. Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
  4. Save and restart the ONT/modem.
FRITZ!Box
  1. Internet → Account Information → Internet service provider: Other Internet service provider.
  2. Connection: external modem or router (LAN 1 as WAN).
  3. Account information required: Yes — username user@spark.co.nz, password password.
  4. Use VLAN for internet access: on, VLAN ID 10.
  5. Apply and restart the ONT/modem.
eero / Nest
  1. eero app → Settings → Network settings → ISP settings: PPPoE (username user@spark.co.nz, password password); VLAN ID 10.
  2. Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: PPPoE; VLAN 10 where your firmware offers it.
WAN authPPPoE
VLAN10
PCP0
Physical handoffEthernet from ONT

The ONT stays

The Spark Fibre box/ONT handles the optical side. Your router connects to the active ONT Ethernet port and establishes the WAN session.

Credentials are generic, but not blank

Spark says a specific username/password is not required, but both fields must be non-empty. Its example values are user@spark.co.nz and password.

VLAN is mandatory in the cited profile

Unlike Skinny Fibre, Spark's current BYO Fibre instructions require 802.1Q VLAN ID 10.

Next step

Evidence

Page reviewed 6 November 2026 · compatibility dataset snapshot 23 September 2026.