HHLONIX
EN

New Zealand · Slingshot

Can I use my own router with Slingshot Fibre?

Yes. Slingshot publishes BYO fibre modem settings: DHCP (IP over Ethernet) with no username or password, 802.1Q VLAN 10 with priority 0, and MTU 1500 or 1492. Most modems connect automatically once the service is live.

Fibre-optic broadband infrastructure
Illustrative photograph; equipment and compatibility may differ.Profpcde · CC0 1.0 · Wikimedia Commons
Page reviewed 5 November 2026Dataset snapshot 23 September 2026Cited sources 1How Hlonix verifies →

Quick reference

Own-router settings at a glance

From official provider sources cited below. Pick your router for a full verdict with topology and caveats.

Slingshot Fibre — BYO modem

Own-router path
Own router connects directly
Physical handoff
Fibre ONT → Ethernet WAN
WAN connection
DHCP
VLAN
VLAN 10 (802.1Q tagged)
ISP phone / voice
Check with your provider
ISP TV
Check with your provider
Evidence confidence
High — official provider source

Settings to enter on your router

  1. Connect the router WAN port to the fibre ONT.
  2. Use DHCP / IPoE (automatic or dynamic IP) — no PPPoE username or password.
  3. Enable 802.1Q VLAN tagging with VLAN ID 10 and priority (PCP) 0.
  4. Use MTU 1500 (1492 also listed) and leave NAT enabled.
  5. BigPipe/Skinny modems and 2degrees/Orcon FRITZ!Box units need manual setup; most other modems connect once the line is live.

Copy-paste router configuration

Generated from the settings above. Menu names vary by firmware version.

OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan.10'
uci set network.wan.proto='dhcp'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restart
MikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/interface vlan add name=wan-vlan10 vlan-id=10 interface=ether1
/ip dhcp-client add interface=wan-vlan10 disabled=no
/interface list member add list=WAN interface=wan-vlan10
UniFi
  1. Settings → Internet → select the WAN (Primary) → Advanced: Manual.
  2. VLAN ID: on, 10.
  3. IPv4 connection: DHCP.
  4. Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
  1. Interfaces → VLANs (OPNsense: Interfaces → Other Types → VLAN): parent = WAN NIC, tag 10, priority 0.
  2. Interfaces → Assignments: assign the new VLAN as WAN.
  3. WAN → IPv4 configuration type: DHCP.
  4. Save, apply, then power-cycle the ONT/modem.
ASUS
  1. WAN → Internet Connection → WAN Connection Type: Automatic IP.
  2. LAN → IPTV → Select ISP Profile: Manual → Internet: VID 10, PRIO 0.
  3. Apply and reboot the ONT/modem.
TP-Link
  1. Advanced → Network → Internet: connection type Dynamic IP.
  2. Advanced → Network → IPTV/VLAN: enable, Mode Custom, Internet VLAN ID 10.
  3. Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
  4. Save and restart the ONT/modem.
FRITZ!Box
  1. Internet → Account Information → Internet service provider: Other Internet service provider.
  2. Connection: external modem or router (LAN 1 as WAN).
  3. Account information required: No.
  4. Use VLAN for internet access: on, VLAN ID 10.
  5. Apply and restart the ONT/modem.
eero / Nest
  1. eero app → Settings → Network settings → ISP settings: leave on automatic/DHCP; VLAN ID 10.
  2. Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: DHCP; VLAN 10 where your firmware offers it.
WAN authDHCP / IPoE
VLAN10 (802.1Q)
Priority / PCP0
MTU1500 or 1492

Same family, same fibre profile

2degrees, Slingshot and Orcon are part of the same group and their current help pages publish the same fibre WAN values: DHCP, VLAN 10, priority 0. This differs from Spark and Skinny, which use PPPoE.

Do not set PPPoE on fibre

PPPoE credentials are only listed for VDSL lines in 2degrees' help. On fibre the router should obtain its address automatically over VLAN 10; a PPPoE session will not come up.

Modems that need manual setup

Slingshot notes that BigPipe or Skinny modems and FRITZ!Box units supplied by 2degrees or Orcon must be configured by hand. If your modem still fails, Slingshot says it can send one of its own.

Next step

Evidence

Page reviewed 5 November 2026 · compatibility dataset snapshot 23 September 2026.