HHLONIX
EN

New Zealand · Voyager

Can I use my own router with Voyager?

Yes. Voyager documents DHCP / IPoE on VLAN 10. Phone service needs the provider device.

Ethernet cable and network connections
Illustrative photograph; equipment and compatibility may differ.Tony Webster · CC BY 2.0 · Wikimedia Commons
Page reviewed 6 November 2026Profile researched 6 November 2026Cited sources 1How Hlonix verifies →

Quick reference

Own-router settings at a glance

From official provider sources cited below. Pick your router for a full verdict with topology and caveats.

Voyager UFB Fibre — own router (IPoE/DHCP)

Own-router path
Own router connects directly
Physical handoff
Fibre ONT → Ethernet WAN
WAN connection
DHCP
VLAN
VLAN 10 (802.1Q tagged)
ISP phone / voice
Provider hub required
ISP TV
Check with your provider
Evidence confidence
High — official provider source

Settings to enter on your router

  1. Connect a router with a gigabit (or faster) Ethernet WAN port to the ONT.
  2. Enable WAN VLAN tagging with VLAN ID 10 and 802.1p priority 0.
  3. Set the connection type to DHCP (IPoE); MTU 1500, MSS 1460.
  4. For IPv6, enable a DHCPv6 client using IA_NA for the WAN address and request a /56 prefix delegation.

Copy-paste router configuration

Generated from the settings above. Menu names vary by firmware version.

OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan.10'
uci set network.wan.proto='dhcp'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restart
MikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/interface vlan add name=wan-vlan10 vlan-id=10 interface=ether1
/ip dhcp-client add interface=wan-vlan10 disabled=no
/interface list member add list=WAN interface=wan-vlan10
UniFi
  1. Settings → Internet → select the WAN (Primary) → Advanced: Manual.
  2. VLAN ID: on, 10.
  3. IPv4 connection: DHCP.
  4. Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
  1. Interfaces → VLANs (OPNsense: Interfaces → Other Types → VLAN): parent = WAN NIC, tag 10, priority 0.
  2. Interfaces → Assignments: assign the new VLAN as WAN.
  3. WAN → IPv4 configuration type: DHCP.
  4. Save, apply, then power-cycle the ONT/modem.
ASUS
  1. WAN → Internet Connection → WAN Connection Type: Automatic IP.
  2. LAN → IPTV → Select ISP Profile: Manual → Internet: VID 10, PRIO 0.
  3. Apply and reboot the ONT/modem.
TP-Link
  1. Advanced → Network → Internet: connection type Dynamic IP.
  2. Advanced → Network → IPTV/VLAN: enable, Mode Custom, Internet VLAN ID 10.
  3. Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
  4. Save and restart the ONT/modem.
FRITZ!Box
  1. Internet → Account Information → Internet service provider: Other Internet service provider.
  2. Connection: external modem or router (LAN 1 as WAN).
  3. Account information required: No.
  4. Use VLAN for internet access: on, VLAN ID 10.
  5. Apply and restart the ONT/modem.
eero / Nest
  1. eero app → Settings → Network settings → ISP settings: leave on automatic/DHCP; VLAN ID 10.
  2. Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: DHCP; VLAN 10 where your firmware offers it.

Voyager UFB Fibre — own router (PPPoE)

Own-router path
Own router connects directly
Physical handoff
Fibre ONT → Ethernet WAN
WAN connection
PPPoE
VLAN
VLAN 10 (802.1Q tagged)
ISP phone / voice
Provider hub required
ISP TV
Check with your provider
Evidence confidence
High — official provider source

Settings to enter on your router

  1. Connect the router's Ethernet WAN port to the ONT.
  2. Enable WAN VLAN tagging with ID 10, priority 0.
  3. Choose PPPoE and enter your username in the form user@vygr.net with the password from your Broadband Configuration Details email.
  4. Set MTU 1492 (MSS 1452); enable IPv6CP and DHCPv6-PD to receive a /56.

Copy-paste router configuration

Generated from the settings above. Use the broadband username and password from your provider account or welcome email. Menu names vary by firmware version.

OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan.10'
uci set network.wan.proto='pppoe'
uci set network.wan.username='YOUR_BROADBAND_USERNAME'
uci set network.wan.password='YOUR_BROADBAND_PASSWORD'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restart
MikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/interface vlan add name=wan-vlan10 vlan-id=10 interface=ether1
/interface pppoe-client add name=pppoe-out1 interface=wan-vlan10 user="YOUR_BROADBAND_USERNAME" password="YOUR_BROADBAND_PASSWORD" add-default-route=yes use-peer-dns=yes disabled=no
/interface list member add list=WAN interface=pppoe-out1
UniFi
  1. Settings → Internet → select the WAN (Primary) → Advanced: Manual.
  2. VLAN ID: on, 10.
  3. IPv4 connection: PPPoE — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
  4. Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
  1. Interfaces → VLANs (OPNsense: Interfaces → Other Types → VLAN): parent = WAN NIC, tag 10, priority 0.
  2. Interfaces → Assignments: assign the new VLAN as WAN.
  3. WAN → IPv4 configuration type: PPPoE, username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
  4. Save, apply, then power-cycle the ONT/modem.
ASUS
  1. WAN → Internet Connection → WAN Connection Type: PPPoE; enter username YOUR_BROADBAND_USERNAME and password YOUR_BROADBAND_PASSWORD.
  2. LAN → IPTV → Select ISP Profile: Manual → Internet: VID 10, PRIO 0.
  3. Apply and reboot the ONT/modem.
TP-Link
  1. Advanced → Network → Internet: connection type PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD).
  2. Advanced → Network → IPTV/VLAN: enable, Mode Custom, Internet VLAN ID 10.
  3. Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
  4. Save and restart the ONT/modem.
FRITZ!Box
  1. Internet → Account Information → Internet service provider: Other Internet service provider.
  2. Connection: external modem or router (LAN 1 as WAN).
  3. Account information required: Yes — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
  4. Use VLAN for internet access: on, VLAN ID 10.
  5. Apply and restart the ONT/modem.
eero / Nest
  1. eero app → Settings → Network settings → ISP settings: PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD); VLAN ID 10.
  2. Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: PPPoE; VLAN 10 where your firmware offers it.
WAN authDHCP / IPoE
VLAN10 (802.1Q tagged)
Priority / PCP0
MTU1500

What Voyager officially documents

Connect a router with a gigabit (or faster) Ethernet WAN port to the ONT. Enable WAN VLAN tagging with VLAN ID 10 and 802.1p priority 0. Set the connection type to DHCP (IPoE); MTU 1500, MSS 1460. For IPv6, enable a DHCPv6 client using IA_NA for the WAN address and request a /56 prefix delegation. Connect the router's Ethernet WAN port to the ONT. Enable WAN VLAN tagging with ID 10, priority 0. Choose PPPoE and enter your username in the form user@vygr.net with the password from your Broadband Configuration Details email. Set MTU 1492 (MSS 1452); enable IPv6CP and DHCPv6-PD to receive a /56.

Before you remove the Voyager box

Phone service on this connection depends on the provider device. TV services may use their own VLAN or box; check before swapping. Since May 2024 Voyager uses circuit-based authentication, so only one of IPoE or PPPoE works at a time on a line. Untagged is possible on request but not recommended. Voice only on Voyager-supplied hardware. Page footer © 2023.

Common setup mistakes

Choose Dynamic IP / DHCP (IPoE), not PPPoE — there is no broadband login to enter. Tag the WAN with VLAN 10; a missing or wrong tag is the most common reason a new router gets no connection. MSS 1460; IPv6 via DHCPv6 IA_NA on WAN + DHCPv6-PD /56 Power-cycle the ONT or modem after swapping routers so it releases the old session.

Next step

Evidence

Page reviewed 6 November 2026 · profile researched 6 November 2026.