HHLONIX
EN

Canada · TekSavvy

Can I use my own router with TekSavvy?

Only behind the provider device. Provider modem stays in front of your router. Check phone and TV services before you remove the provider box.

Network equipment and server rack
Illustrative photograph; equipment and compatibility may differ.Shixart1985 · CC BY 2.0 · Wikimedia Commons
Page reviewed 6 November 2026Profile researched 6 November 2026Cited sources 1How Hlonix verifies →

Quick reference

Own-router settings at a glance

From official provider sources cited below. Pick your router for a full verdict with topology and caveats.

TekSavvy Fibre — customer-supplied modems not allowed

Own-router path
Provider modem stays in front of your router
Physical handoff
Fibre → TekSavvy-supplied equipment
WAN connection
Handled by the cable modem
VLAN
Handled by provider device
ISP phone / voice
Check with your provider
ISP TV
Check with your provider
Evidence confidence
High — official provider source

Settings to enter on your router

  1. Keep the TekSavvy-supplied fibre modem — TekSavvy does not allow customer modems on Fibre.
  2. If you want your own router, connect it behind the TekSavvy modem; no WAN settings are published for this.
  3. Contact TekSavvy support for any configuration help.

TekSavvy DSL/VDSL — own modem (PPPoE)

Own-router path
Your own compatible modem + router
Physical handoff
Phone line → your VDSL/ADSL2+ modem (PPPoE)
WAN connection
PPPoE
VLAN
Confirm with provider
ISP phone / voice
Check with your provider
ISP TV
Check with your provider
Evidence confidence
Medium — verify account details

Settings to enter on your router

  1. Check your plan: ADSL2+ for 15/1 and lower, VDSL for 15/10 and higher.
  2. In Ontario/Quebec use a supported VDSL modem (SmartRG, Sagemcom Home Hub or listed TP-Link models); in Alberta/BC any VDSL modem works.
  3. Configure the modem's internet connection as PPPoE using the account login TekSavvy gives you.
  4. Consult the modem manufacturer's manual for where to enter the PPPoE details; TekSavvy does not publish VLAN/MTU values.
Own-router pathProvider modem stays in front of your router
WANHandled by the cable modem
PhoneCheck with your provider
TVCheck with your provider

What TekSavvy officially documents

Keep the TekSavvy-supplied fibre modem — TekSavvy does not allow customer modems on Fibre. If you want your own router, connect it behind the TekSavvy modem; no WAN settings are published for this. Contact TekSavvy support for any configuration help. Check your plan: ADSL2+ for 15/1 and lower, VDSL for 15/10 and higher. In Ontario/Quebec use a supported VDSL modem (SmartRG, Sagemcom Home Hub or listed TP-Link models); in Alberta/BC any VDSL modem works. Configure the modem's internet connection as PPPoE using the account login TekSavvy gives you. Consult the modem manufacturer's manual for where to enter the PPPoE details; TekSavvy does not publish VLAN/MTU values.

Before you remove the TekSavvy box

The official page does not settle phone service for a third-party router — confirm before you disconnect the provider box. TV services may use their own VLAN or box; check before swapping. No VLAN, PPPoE or MTU values are published. Whether a router behind the TekSavvy modem needs special settings is not stated.

Common setup mistakes

If the provider device must stay, put your own router behind it and avoid double NAT: use the provider's bridge, modem or passthrough option where one exists, otherwise run your router in access-point mode.

Next step

Evidence

Page reviewed 6 November 2026 · profile researched 6 November 2026.