United Kingdom · Andrews & Arnold
Can I use my own router with Andrews & Arnold?
Yes. Andrews & Arnold documents PPPoE with no VLAN tag with your account's broadband login.
%2C_LSA-Tool_and_crimping_tool.jpg/960px-Cable_stripper%2C_cable_tester_(RJ45%2C_RJ11)%2C_LSA-Tool_and_crimping_tool.jpg)
Quick reference
Own-router settings at a glance
From official provider sources cited below. Pick your router for a full verdict with topology and caveats.
A&A FTTP (Openreach) — own router via PPPoE, untagged
- Own-router path
- Own router connects directly
- Physical handoff
- Openreach fibre ONT → Ethernet WAN
- WAN connection
- PPPoE
- VLAN
- None — untagged
- ISP phone / voice
- No dependency documented
- ISP TV
- No dependency documented
- Evidence confidence
- High — official provider source
Settings to enter on your router
- Plug the router WAN port into the Openreach ONT.
- Select PPPoE with no VLAN tag (untagged).
- Enter the login (name@realm.N format) and password issued by A&A; the password can be changed in the Broadband Control Pages.
- Set MTU to 1500 if your router supports RFC4638 baby jumbo frames.
- Leave WAN IP addresses on automatic (assigned via PPP); DNS can come from PPP or be set manually.
Copy-paste router configuration
Generated from the settings above. Use the broadband username and password from your provider account or welcome email. Menu names vary by firmware version.
OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan'
uci set network.wan.proto='pppoe'
uci set network.wan.username='YOUR_BROADBAND_USERNAME'
uci set network.wan.password='YOUR_BROADBAND_PASSWORD'
# Provider lists MTU 1500: only set mtu 1500 if your hardware supports RFC 4638 baby jumbo frames.
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restartMikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/interface pppoe-client add name=pppoe-out1 interface=ether1 user="YOUR_BROADBAND_USERNAME" password="YOUR_BROADBAND_PASSWORD" add-default-route=yes use-peer-dns=yes disabled=no
/interface list member add list=WAN interface=pppoe-out1UniFi
- Settings → Internet → select the WAN (Primary) → Advanced: Manual.
- VLAN ID: off.
- IPv4 connection: PPPoE — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
- Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
- Use the physical WAN NIC as WAN.
- WAN → IPv4 configuration type: PPPoE, username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
- Save, apply, then power-cycle the ONT/modem.
ASUS
- WAN → Internet Connection → WAN Connection Type: PPPoE; enter username YOUR_BROADBAND_USERNAME and password YOUR_BROADBAND_PASSWORD.
- LAN → IPTV: leave ISP Profile on None.
- Apply and reboot the ONT/modem.
TP-Link
- Advanced → Network → Internet: connection type PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD).
- IPTV/VLAN: leave disabled.
- Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
- Save and restart the ONT/modem.
FRITZ!Box
- Internet → Account Information → Internet service provider: Other Internet service provider.
- Connection: external modem or router (LAN 1 as WAN).
- Account information required: Yes — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
- Use VLAN for internet access: off.
- Apply and restart the ONT/modem.
eero / Nest
- eero app → Settings → Network settings → ISP settings: PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD).
- Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: PPPoE.
Instant verdict for your router:eero 6+Deco X50/X55ASUS RT-AX86U ProArcher BE550Orbi RBK760Nest Wifi ProOther router
A&A FTTP (CityFibre) — own router via PPPoE on VLAN 911
- Own-router path
- Own router connects directly
- Physical handoff
- CityFibre ONT → Ethernet WAN
- WAN connection
- PPPoE
- VLAN
- VLAN 911 (802.1Q tagged)
- ISP phone / voice
- No dependency documented
- ISP TV
- No dependency documented
- Evidence confidence
- Medium — verify account details
Settings to enter on your router
- Plug the router WAN port into the CityFibre ONT.
- Enable VLAN tagging on the WAN with VLAN ID 911.
- Select PPPoE and enter the login and password issued by A&A.
- Leave WAN IP on automatic; save and reconnect.
Copy-paste router configuration
Generated from the settings above. Use the broadband username and password from your provider account or welcome email. Menu names vary by firmware version.
OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan.911'
uci set network.wan.proto='pppoe'
uci set network.wan.username='YOUR_BROADBAND_USERNAME'
uci set network.wan.password='YOUR_BROADBAND_PASSWORD'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restartMikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/interface vlan add name=wan-vlan911 vlan-id=911 interface=ether1
/interface pppoe-client add name=pppoe-out1 interface=wan-vlan911 user="YOUR_BROADBAND_USERNAME" password="YOUR_BROADBAND_PASSWORD" add-default-route=yes use-peer-dns=yes disabled=no
/interface list member add list=WAN interface=pppoe-out1UniFi
- Settings → Internet → select the WAN (Primary) → Advanced: Manual.
- VLAN ID: on, 911.
- IPv4 connection: PPPoE — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
- Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
- Interfaces → VLANs (OPNsense: Interfaces → Other Types → VLAN): parent = WAN NIC, tag 911, priority 0.
- Interfaces → Assignments: assign the new VLAN as WAN.
- WAN → IPv4 configuration type: PPPoE, username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
- Save, apply, then power-cycle the ONT/modem.
ASUS
- WAN → Internet Connection → WAN Connection Type: PPPoE; enter username YOUR_BROADBAND_USERNAME and password YOUR_BROADBAND_PASSWORD.
- LAN → IPTV → Select ISP Profile: Manual → Internet: VID 911, PRIO 0.
- Apply and reboot the ONT/modem.
TP-Link
- Advanced → Network → Internet: connection type PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD).
- Advanced → Network → IPTV/VLAN: enable, Mode Custom, Internet VLAN ID 911.
- Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
- Save and restart the ONT/modem.
FRITZ!Box
- Internet → Account Information → Internet service provider: Other Internet service provider.
- Connection: external modem or router (LAN 1 as WAN).
- Account information required: Yes — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
- Use VLAN for internet access: on, VLAN ID 911.
- Apply and restart the ONT/modem.
eero / Nest
- eero app → Settings → Network settings → ISP settings: PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD); VLAN ID 911.
- Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: PPPoE; VLAN 911 where your firmware offers it.
Instant verdict for your router:eero 6+Deco X50/X55ASUS RT-AX86U ProArcher BE550Orbi RBK760Nest Wifi ProOther router
Other UK ISPs:EEVodafoneVirgin MediaPlusnetBTSkyTalkTalkZen InternetCommunity FibreYouFibreGigaclearCuckooCompare all UK ISP settings
What Andrews & Arnold officially documents
Plug the router WAN port into the Openreach ONT. Select PPPoE with no VLAN tag (untagged). Enter the login (name@realm.N format) and password issued by A&A; the password can be changed in the Broadband Control Pages. Set MTU to 1500 if your router supports RFC4638 baby jumbo frames. Leave WAN IP addresses on automatic (assigned via PPP); DNS can come from PPP or be set manually. Plug the router WAN port into the CityFibre ONT. Enable VLAN tagging on the WAN with VLAN ID 911. Select PPPoE and enter the login and password issued by A&A. Leave WAN IP on automatic; save and reconnect.
Before you remove the Andrews & Arnold box
The official page does not settle phone service for a third-party router — confirm before you disconnect the provider box. No TV dependency is documented. If you change the password in the control pages, update the router too. If the router cannot handle a long password, A&A support can issue a shorter one. FTTC/VDSL uses PPPoE on VLAN 101 (not needed with an Openreach modem). Page last modified 1 October 2026.
Common setup mistakes
Choose PPPoE, not Dynamic IP — the line will not come up with DHCP alone. Leave WAN VLAN tagging off; adding a tag here breaks the connection. MTU 1500 via RFC4638 (baby jumbo frames); DNS 217.169.20.20 / 217.169.20.21 Power-cycle the ONT or modem after swapping routers so it releases the old session.
Next step
Evidence
Page reviewed 6 November 2026 · profile researched 6 November 2026.