HHLONIX
EN

United Kingdom · Plusnet

Can I use my own router with Plusnet?

Yes, with hardware that matches the access type. Full Fibre connects through the Openreach ONT using PPPoE credentials. Plusnet Fibre / FTTC needs a VDSL modem-router and its published fibre settings include VLAN 101.

Networking installation tools
Illustrative photograph; equipment and compatibility may differ.www.heimnetzwerke.net · CC BY 4.0 · Wikimedia Commons
Page reviewed 6 November 2026Dataset snapshot 23 September 2026Cited sources 2How Hlonix verifies →

Quick reference

Own-router settings at a glance

From official provider sources cited below. Pick your router for a full verdict with topology and caveats.

Plusnet Full Fibre (FTTP)

Own-router path
Own router connects directly
Physical handoff
Openreach FTTP / ONT
WAN connection
PPPoE
VLAN
None — untagged
ISP phone / voice
No dependency documented
ISP TV
No dependency documented
Evidence confidence
High — official provider source

Settings to enter on your router

  1. Connect the router WAN port directly to the Openreach ONT.
  2. Use PPPoE with your Plusnet broadband username and account password.
  3. Use the Plusnet settings for a router connected to an Openreach modem/ONT; no router-side VLAN is listed in that subsection.

Copy-paste router configuration

Generated from the settings above. Use the broadband username and password from your provider account or welcome email. Menu names vary by firmware version.

OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan'
uci set network.wan.proto='pppoe'
uci set network.wan.username='YOUR_BROADBAND_USERNAME'
uci set network.wan.password='YOUR_BROADBAND_PASSWORD'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restart
MikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/interface pppoe-client add name=pppoe-out1 interface=ether1 user="YOUR_BROADBAND_USERNAME" password="YOUR_BROADBAND_PASSWORD" add-default-route=yes use-peer-dns=yes disabled=no
/interface list member add list=WAN interface=pppoe-out1
UniFi
  1. Settings → Internet → select the WAN (Primary) → Advanced: Manual.
  2. VLAN ID: off.
  3. IPv4 connection: PPPoE — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
  4. Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
  1. Use the physical WAN NIC as WAN.
  2. WAN → IPv4 configuration type: PPPoE, username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
  3. Save, apply, then power-cycle the ONT/modem.
ASUS
  1. WAN → Internet Connection → WAN Connection Type: PPPoE; enter username YOUR_BROADBAND_USERNAME and password YOUR_BROADBAND_PASSWORD.
  2. LAN → IPTV: leave ISP Profile on None.
  3. Apply and reboot the ONT/modem.
TP-Link
  1. Advanced → Network → Internet: connection type PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD).
  2. IPTV/VLAN: leave disabled.
  3. Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
  4. Save and restart the ONT/modem.
FRITZ!Box
  1. Internet → Account Information → Internet service provider: Other Internet service provider.
  2. Connection: external modem or router (LAN 1 as WAN).
  3. Account information required: Yes — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
  4. Use VLAN for internet access: off.
  5. Apply and restart the ONT/modem.
eero / Nest
  1. eero app → Settings → Network settings → ISP settings: PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD).
  2. Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: PPPoE.

Plusnet Fibre (FTTC/VDSL)

Own-router path
Own router connects directly
Physical handoff
FTTC / VDSL over phone line
WAN connection
PPPoE
VLAN
VLAN 101 (802.1Q tagged)
ISP phone / voice
No dependency documented
ISP TV
No dependency documented
Evidence confidence
High — official provider source

Settings to enter on your router

  1. Use a VDSL-capable modem/router.
  2. Use PPPoE with your Plusnet broadband username and account password.
  3. Enable VLAN tagging with VLAN ID 101 and priority 0.

Copy-paste router configuration

Generated from the settings above. Use the broadband username and password from your provider account or welcome email. Menu names vary by firmware version.

UniFi
  1. Settings → Internet → select the WAN (Primary) → Advanced: Manual.
  2. VLAN ID: on, 101.
  3. IPv4 connection: PPPoE — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
  4. Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
  1. Interfaces → VLANs (OPNsense: Interfaces → Other Types → VLAN): parent = WAN NIC, tag 101, priority 0.
  2. Interfaces → Assignments: assign the new VLAN as WAN.
  3. WAN → IPv4 configuration type: PPPoE, username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
  4. Save, apply, then power-cycle the ONT/modem.
ASUS
  1. WAN → Internet Connection → WAN Connection Type: PPPoE; enter username YOUR_BROADBAND_USERNAME and password YOUR_BROADBAND_PASSWORD.
  2. LAN → IPTV → Select ISP Profile: Manual → Internet: VID 101, PRIO 0.
  3. Apply and reboot the ONT/modem.
TP-Link
  1. Advanced → Network → Internet: connection type PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD).
  2. Advanced → Network → IPTV/VLAN: enable, Mode Custom, Internet VLAN ID 101.
  3. Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
  4. Save and restart the ONT/modem.
FRITZ!Box
  1. Internet → Account Information → Internet service provider: Other Internet service provider.
  2. Connection: via DSL (VDSL).
  3. Account information required: Yes — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
  4. Use VLAN for internet access: on, VLAN ID 101.
  5. Apply and restart the ONT/modem.
eero / Nest
  1. eero app → Settings → Network settings → ISP settings: PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD); VLAN ID 101.
  2. Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: PPPoE; VLAN 101 where your firmware offers it.
Full Fibre / FTTPPPPoE via Openreach ONT
Fibre / FTTCVDSL + PPPoE + VLAN 101
CredentialsPlusnet broadband username + account password
Support fallbackKeep the Plusnet hub available for diagnostics

Full Fibre

The ONT handles the optical side, leaving the third-party router to establish the PPPoE session over Ethernet.

FTTC

The replacement device must also be the DSL modem. That makes VDSL and VLAN support just as important as PPPoE.

Credentials

Plusnet publishes the broadband username/password pattern for third-party equipment. Use account-specific values rather than copying credentials from a generic example.

Next step

Evidence

Page reviewed 6 November 2026 · compatibility dataset snapshot 23 September 2026.