United Kingdom · EE
Can I use my own router with EE Broadband?
Yes, but the hardware requirements change with the access type. EE Full Fibre can use a compatible PPPoE router directly on the ONT; Part Fibre / SOGEA needs VDSL plus VLAN 101. Digital Home Phone and EE TV remain hub-dependent.

Quick reference
Own-router settings at a glance
From official provider sources cited below. Pick your router for a full verdict with topology and caveats.
EE Full Fibre (FTTP)
- Own-router path
- Own router connects directly
- Physical handoff
- Openreach FTTP / ONT
- WAN connection
- PPPoE
- VLAN
- None — untagged
- ISP phone / voice
- Provider hub required
- ISP TV
- Provider hub required
- Evidence confidence
- High — official provider source
Settings to enter on your router
- Connect the router WAN port to the Openreach ONT.
- Use PPPoE authentication.
- EE documents no VLAN tagging for Full Fibre.
- Keep the EE/BT hub if you need Digital Home Phone, EE TV or another hub-dependent EE service.
Copy-paste router configuration
Generated from the settings above. Use the broadband username and password from your provider account or welcome email. Menu names vary by firmware version.
OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan'
uci set network.wan.proto='pppoe'
uci set network.wan.username='YOUR_BROADBAND_USERNAME'
uci set network.wan.password='YOUR_BROADBAND_PASSWORD'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restartMikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/interface pppoe-client add name=pppoe-out1 interface=ether1 user="YOUR_BROADBAND_USERNAME" password="YOUR_BROADBAND_PASSWORD" add-default-route=yes use-peer-dns=yes disabled=no
/interface list member add list=WAN interface=pppoe-out1UniFi
- Settings → Internet → select the WAN (Primary) → Advanced: Manual.
- VLAN ID: off.
- IPv4 connection: PPPoE — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
- Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
- Use the physical WAN NIC as WAN.
- WAN → IPv4 configuration type: PPPoE, username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
- Save, apply, then power-cycle the ONT/modem.
ASUS
- WAN → Internet Connection → WAN Connection Type: PPPoE; enter username YOUR_BROADBAND_USERNAME and password YOUR_BROADBAND_PASSWORD.
- LAN → IPTV: leave ISP Profile on None.
- Apply and reboot the ONT/modem.
TP-Link
- Advanced → Network → Internet: connection type PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD).
- IPTV/VLAN: leave disabled.
- Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
- Save and restart the ONT/modem.
FRITZ!Box
- Internet → Account Information → Internet service provider: Other Internet service provider.
- Connection: external modem or router (LAN 1 as WAN).
- Account information required: Yes — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
- Use VLAN for internet access: off.
- Apply and restart the ONT/modem.
eero / Nest
- eero app → Settings → Network settings → ISP settings: PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD).
- Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: PPPoE.
Instant verdict for your router:eero 6+Deco X50/X55ASUS RT-AX86U ProArcher BE550Orbi RBK760Nest Wifi ProOther router
EE Part Fibre / SOGEA (FTTC/VDSL)
- Own-router path
- Own router connects directly
- Physical handoff
- Copper phone-line last mile / VDSL
- WAN connection
- PPPoE
- VLAN
- VLAN 101 (802.1Q tagged)
- ISP phone / voice
- Provider hub required
- ISP TV
- Provider hub required
- Evidence confidence
- High — official provider source
Settings to enter on your router
- Use a VDSL-capable modem/router.
- Use PPPoE authentication.
- Enable VLAN tagging with VLAN ID 101 and priority 0.
- Keep the EE/BT hub if you need Digital Home Phone, EE TV or another hub-dependent EE service.
Copy-paste router configuration
Generated from the settings above. Use the broadband username and password from your provider account or welcome email. Menu names vary by firmware version.
UniFi
- Settings → Internet → select the WAN (Primary) → Advanced: Manual.
- VLAN ID: on, 101.
- IPv4 connection: PPPoE — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
- Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
- Interfaces → VLANs (OPNsense: Interfaces → Other Types → VLAN): parent = WAN NIC, tag 101, priority 0.
- Interfaces → Assignments: assign the new VLAN as WAN.
- WAN → IPv4 configuration type: PPPoE, username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
- Save, apply, then power-cycle the ONT/modem.
ASUS
- WAN → Internet Connection → WAN Connection Type: PPPoE; enter username YOUR_BROADBAND_USERNAME and password YOUR_BROADBAND_PASSWORD.
- LAN → IPTV → Select ISP Profile: Manual → Internet: VID 101, PRIO 0.
- Apply and reboot the ONT/modem.
TP-Link
- Advanced → Network → Internet: connection type PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD).
- Advanced → Network → IPTV/VLAN: enable, Mode Custom, Internet VLAN ID 101.
- Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
- Save and restart the ONT/modem.
FRITZ!Box
- Internet → Account Information → Internet service provider: Other Internet service provider.
- Connection: via DSL (VDSL).
- Account information required: Yes — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
- Use VLAN for internet access: on, VLAN ID 101.
- Apply and restart the ONT/modem.
eero / Nest
- eero app → Settings → Network settings → ISP settings: PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD); VLAN ID 101.
- Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: PPPoE; VLAN 101 where your firmware offers it.
Instant verdict for your router:eero 6+Deco X50/X55ASUS RT-AX86U ProArcher BE550Orbi RBK760Nest Wifi ProOther router
Other UK ISPs:VodafoneVirgin MediaPlusnetBTSkyTalkTalkZen InternetCommunity FibreYouFibreGigaclearCuckooAndrews & ArnoldCompare all UK ISP settings
Full Fibre path
The Openreach ONT terminates the fiber, so the third-party router needs Ethernet WAN and PPPoE rather than a built-in fiber modem.
Part Fibre / SOGEA path
The copper last mile reaches the premises as VDSL. A router-only mesh cannot plug directly into that line; the replacement device needs VDSL plus EE's documented VLAN settings.
Services that keep the hub
A pure internet replacement can be technically compatible while Digital Home Phone or EE TV still changes the topology. Hlonix treats those as separate inputs.
Next step
Evidence
- EE — using and configuring a third-party router (official ISP)
Page reviewed 6 November 2026 · compatibility dataset snapshot 23 September 2026.