HHLONIX
EN

Australia · Aussie Broadband

Can I use my own router with Aussie Broadband?

Yes. Aussie Broadband publishes a straightforward BYO profile: Dynamic IP/IPoE/DHCP, no broadband username/password and VLAN disabled for the cited nbn settings. FTTN/FTTB still needs a VDSL-capable modem-router.

Ethernet cable and network connections
Illustrative photograph; equipment and compatibility may differ.Tony Webster · CC BY 2.0 · Wikimedia Commons
Page reviewed 6 November 2026Dataset snapshot 23 September 2026Cited sources 1How Hlonix verifies →

Quick reference

Own-router settings at a glance

From official provider sources cited below. Pick your router for a full verdict with topology and caveats.

Aussie Broadband — FTTP / HFC / FTTC / Fixed Wireless / Opticomm

Own-router path
Own router connects directly
Physical handoff
nbn/Opticomm connection box → Ethernet WAN
WAN connection
DHCP
VLAN
None — untagged
ISP phone / voice
Check with your provider
ISP TV
No dependency documented
Evidence confidence
High — official provider source

Settings to enter on your router

  1. Use Dynamic IP / IPoE / DHCP / Automatic IP.
  2. Disable VLAN tagging.
  3. Do not enter a broadband username/password for the standard cited setup.

Copy-paste router configuration

Generated from the settings above. Menu names vary by firmware version.

OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan'
uci set network.wan.proto='dhcp'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restart
MikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/ip dhcp-client add interface=ether1 disabled=no
UniFi
  1. Settings → Internet → select the WAN (Primary) → Advanced: Manual.
  2. VLAN ID: off.
  3. IPv4 connection: DHCP.
  4. Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
  1. Use the physical WAN NIC as WAN.
  2. WAN → IPv4 configuration type: DHCP.
  3. Save, apply, then power-cycle the ONT/modem.
ASUS
  1. WAN → Internet Connection → WAN Connection Type: Automatic IP.
  2. LAN → IPTV: leave ISP Profile on None.
  3. Apply and reboot the ONT/modem.
TP-Link
  1. Advanced → Network → Internet: connection type Dynamic IP.
  2. IPTV/VLAN: leave disabled.
  3. Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
  4. Save and restart the ONT/modem.
FRITZ!Box
  1. Internet → Account Information → Internet service provider: Other Internet service provider.
  2. Connection: external modem or router (LAN 1 as WAN).
  3. Account information required: No.
  4. Use VLAN for internet access: off.
  5. Apply and restart the ONT/modem.
eero / Nest
  1. eero app → Settings → Network settings → ISP settings: leave on automatic/DHCP.
  2. Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: DHCP.

Aussie Broadband — FTTN / FTTB VDSL

Own-router path
Own router connects directly
Physical handoff
FTTN/FTTB copper last mile → VDSL modem-router
WAN connection
DHCP
VLAN
None — untagged
ISP phone / voice
Check with your provider
ISP TV
No dependency documented
Evidence confidence
High — official provider source

Settings to enter on your router

  1. Use VDSL/VDSL2 mode.
  2. Use Dynamic IP / IPoE / DHCP / Automatic IP.
  3. Disable VLAN tagging and obtain the IP address automatically.

Copy-paste router configuration

Generated from the settings above. Menu names vary by firmware version.

UniFi
  1. Settings → Internet → select the WAN (Primary) → Advanced: Manual.
  2. VLAN ID: off.
  3. IPv4 connection: DHCP.
  4. Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
  1. Use the physical WAN NIC as WAN.
  2. WAN → IPv4 configuration type: DHCP.
  3. Save, apply, then power-cycle the ONT/modem.
ASUS
  1. WAN → Internet Connection → WAN Connection Type: Automatic IP.
  2. LAN → IPTV: leave ISP Profile on None.
  3. Apply and reboot the ONT/modem.
TP-Link
  1. Advanced → Network → Internet: connection type Dynamic IP.
  2. IPTV/VLAN: leave disabled.
  3. Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
  4. Save and restart the ONT/modem.
FRITZ!Box
  1. Internet → Account Information → Internet service provider: Other Internet service provider.
  2. Connection: via DSL (VDSL).
  3. Account information required: No.
  4. Use VLAN for internet access: off.
  5. Apply and restart the ONT/modem.
eero / Nest
  1. eero app → Settings → Network settings → ISP settings: leave on automatic/DHCP.
  2. Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: DHCP.
WAN protocolDynamic IP / IPoE / DHCP
VLANDisabled
FTTP/HFC/FTTC/FWEthernet WAN
FTTN/FTTBVDSL/VDSL2 required

Ethernet-handoff services

FTTP, HFC, FTTC, Fixed Wireless and Opticomm profiles use Ethernet WAN after the network connection box. Your router does not need to be a DSL modem in those cases.

FTTN/FTTB services

The router/modem connects directly to the DSL line, so VDSL capability becomes mandatory even though the provider authentication remains simple.

Why this is a good compatibility check

A router can support DHCP and still be wrong for FTTN because it lacks VDSL. Hlonix deliberately tests the physical layer before declaring a match.

Next step

Evidence

Page reviewed 6 November 2026 · compatibility dataset snapshot 23 September 2026.