HHLONIX
EN

Australia · SpinTel

Can I use my own router with SpinTel?

Yes. SpinTel documents DHCP / IPoE with no VLAN tag. Check phone and TV services before you remove the provider box.

Network equipment and server rack
Illustrative photograph; equipment and compatibility may differ.Shixart1985 · CC BY 2.0 · Wikimedia Commons
Page reviewed 6 November 2026Profile researched 6 November 2026Cited sources 1How Hlonix verifies →

Quick reference

Own-router settings at a glance

From official provider sources cited below. Pick your router for a full verdict with topology and caveats.

SpinTel nbn FTTP / HFC / FTTC / Fixed Wireless — own modem

Own-router path
Own router connects directly
Physical handoff
nbn connection box (NTD) → Ethernet WAN
WAN connection
DHCP
VLAN
None — untagged
ISP phone / voice
Check with your provider
ISP TV
Check with your provider
Evidence confidence
High — official provider source

Settings to enter on your router

  1. Connect the modem's Ethernet WAN port to the nbn connection box (FTTN/FTTB: VDSL2 to the phone socket).
  2. Set the service type to IPoE / Dynamic / DHCP / Automatic IP.
  3. Set VLAN ID to disabled / none.
  4. Accept defaults for other fields and allow 10–15 minutes to come online.

Copy-paste router configuration

Generated from the settings above. Menu names vary by firmware version.

OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan'
uci set network.wan.proto='dhcp'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restart
MikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/ip dhcp-client add interface=ether1 disabled=no
UniFi
  1. Settings → Internet → select the WAN (Primary) → Advanced: Manual.
  2. VLAN ID: off.
  3. IPv4 connection: DHCP.
  4. Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
  1. Use the physical WAN NIC as WAN.
  2. WAN → IPv4 configuration type: DHCP.
  3. Save, apply, then power-cycle the ONT/modem.
ASUS
  1. WAN → Internet Connection → WAN Connection Type: Automatic IP.
  2. LAN → IPTV: leave ISP Profile on None.
  3. Apply and reboot the ONT/modem.
TP-Link
  1. Advanced → Network → Internet: connection type Dynamic IP.
  2. IPTV/VLAN: leave disabled.
  3. Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
  4. Save and restart the ONT/modem.
FRITZ!Box
  1. Internet → Account Information → Internet service provider: Other Internet service provider.
  2. Connection: external modem or router (LAN 1 as WAN).
  3. Account information required: No.
  4. Use VLAN for internet access: off.
  5. Apply and restart the ONT/modem.
eero / Nest
  1. eero app → Settings → Network settings → ISP settings: leave on automatic/DHCP.
  2. Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: DHCP.
WAN authDHCP / IPoE
VLANNone — untagged
Priority / PCP—
MTUDefault

What SpinTel officially documents

Connect the modem's Ethernet WAN port to the nbn connection box (FTTN/FTTB: VDSL2 to the phone socket). Set the service type to IPoE / Dynamic / DHCP / Automatic IP. Set VLAN ID to disabled / none. Accept defaults for other fields and allow 10–15 minutes to come online.

Before you remove the SpinTel box

The official page does not settle phone service for a third-party router — confirm before you disconnect the provider box. TV services may use their own VLAN or box; check before swapping. Page dated 2 May 2025. No username/password needed. MTU not stated. Home phone on a BYO modem has a separate SpinTel guide.

Common setup mistakes

Choose Dynamic IP / DHCP (IPoE), not PPPoE — there is no broadband login to enter. Leave WAN VLAN tagging off; adding a tag here breaks the connection. Power-cycle the ONT or modem after swapping routers so it releases the old session.

Next step

Evidence

Page reviewed 6 November 2026 · profile researched 6 November 2026.