HHLONIX
EN

Australia · iiNet

Can I use my own router with iiNet?

Yes. iiNet documents PPPoE with a line-dependent VLAN with your account's broadband login. Phone service needs the provider device.

Ethernet cable and network connections
Illustrative photograph; equipment and compatibility may differ.Ajay Suresh · CC BY 2.0 · Wikimedia Commons
Page reviewed 6 November 2026Profile researched 6 November 2026Cited sources 2How Hlonix verifies →

Quick reference

Own-router settings at a glance

From official provider sources cited below. Pick your router for a full verdict with topology and caveats.

iiNet nbn FTTP / HFC / FTTC — own router

Own-router path
Own router connects directly
Physical handoff
nbn connection box (NTD) → Ethernet WAN
WAN connection
PPPoE
VLAN
Confirm with provider
ISP phone / voice
Provider hub required
ISP TV
Check with your provider
Evidence confidence
High — official provider source

Settings to enter on your router

  1. Connect the router WAN port to the nbn connection box and set the mode to Ethernet WAN.
  2. Choose PPPoE; if there is an ISP list, choose 'Other' rather than iiNet.
  3. Enter your full iiNet username including the domain, and your account password (shown in order emails / invoice).
  4. If your plan was activated before March 2023, enable VLAN tagging with ID 2 and 802.1p priority 0; otherwise leave all VLAN settings off.
  5. Some legacy-billed plans use IPoE/DHCP instead of PPPoE; call iiNet if PPPoE fails.

iiNet nbn FTTN / FTTB — own VDSL2 modem

Own-router path
Own router connects directly
Physical handoff
Phone wall socket → VDSL2 (DSL port)
WAN connection
PPPoE
VLAN
Confirm with provider
ISP phone / voice
Provider hub required
ISP TV
Check with your provider
Evidence confidence
High — official provider source

Settings to enter on your router

  1. Connect the VDSL2 modem to the main phone socket.
  2. Set VDSL profile 17a (multimode), PTM transfer mode, and enable G.INP and G.Vector.
  3. Choose PPPoE with your full iiNet username (with domain) and password.
  4. Plans activated before March 2023: VLAN on, ID 2, priority 0; newer plans: VLAN off.
WAN authPPPoE
VLANVaries — confirm for your line
Priority / PCP—
MTUDefault

What iiNet officially documents

Connect the router WAN port to the nbn connection box and set the mode to Ethernet WAN. Choose PPPoE; if there is an ISP list, choose 'Other' rather than iiNet. Enter your full iiNet username including the domain, and your account password (shown in order emails / invoice). If your plan was activated before March 2023, enable VLAN tagging with ID 2 and 802.1p priority 0; otherwise leave all VLAN settings off. Some legacy-billed plans use IPoE/DHCP instead of PPPoE; call iiNet if PPPoE fails. Connect the VDSL2 modem to the main phone socket. Set VDSL profile 17a (multimode), PTM transfer mode, and enable G.INP and G.Vector. Choose PPPoE with your full iiNet username (with domain) and password. Plans activated before March 2023: VLAN on, ID 2, priority 0; newer plans: VLAN off.

Before you remove the iiNet box

Phone service on this connection depends on the provider device. TV services may use their own VLAN or box; check before swapping. MTU not stated. iiNet states nbn Phone and included calls are not available with a BYO modem. nbn Wireless: PPPoE with VLAN 2 priority 0 (legacy plans VLAN off). Home Wireless/5G cannot use BYO. No page date.

Common setup mistakes

Choose PPPoE, not Dynamic IP — the line will not come up with DHCP alone. The VLAN depends on the access network behind your line — confirm it with the provider before configuring the router. VLAN 2 / priority 0 only for plans activated before March 2023; later plans VLAN off. DNS 203.0.178.191 / 203.215.29.191 Power-cycle the ONT or modem after swapping routers so it releases the old session.

Next step

Evidence

Page reviewed 6 November 2026 · profile researched 6 November 2026.