Australia · Telstra
Can I use my own router with Telstra?
Yes on compatible hardware. Telstra publishes BYO settings: IPoE/DHCP/Automatic with VLAN tagging off for current nbn/Opticomm profiles. The hardware requirement changes by connection type: FTTN/FTTB needs VDSL2 in the BYO modem-router; FTTP/HFC/FTTC/Fixed Wireless use an Ethernet handoff from a connection box.

Quick reference
Own-router settings at a glance
From official provider sources cited below. Pick your router for a full verdict with topology and caveats.
Telstra nbn / Opticomm — Ethernet WAN connection types
- Own-router path
- Own router connects directly
- Physical handoff
- FTTP / HFC / FTTC / Fixed Wireless / Opticomm connection box → Ethernet WAN
- WAN connection
- DHCP
- VLAN
- None — untagged
- ISP phone / voice
- Check with your provider
- ISP TV
- No dependency documented
- Evidence confidence
- High — official provider source
Settings to enter on your router
- Use IPoE/DHCP/Automatic for the WAN connection.
- Leave VLAN tagging blank/off/0.
- Connect to the designated UNI-D or Ethernet port on the nbn/Opticomm connection box.
Copy-paste router configuration
Generated from the settings above. Menu names vary by firmware version.
OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan'
uci set network.wan.proto='dhcp'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restartMikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/ip dhcp-client add interface=ether1 disabled=noUniFi
- Settings → Internet → select the WAN (Primary) → Advanced: Manual.
- VLAN ID: off.
- IPv4 connection: DHCP.
- Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
- Use the physical WAN NIC as WAN.
- WAN → IPv4 configuration type: DHCP.
- Save, apply, then power-cycle the ONT/modem.
ASUS
- WAN → Internet Connection → WAN Connection Type: Automatic IP.
- LAN → IPTV: leave ISP Profile on None.
- Apply and reboot the ONT/modem.
TP-Link
- Advanced → Network → Internet: connection type Dynamic IP.
- IPTV/VLAN: leave disabled.
- Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
- Save and restart the ONT/modem.
FRITZ!Box
- Internet → Account Information → Internet service provider: Other Internet service provider.
- Connection: external modem or router (LAN 1 as WAN).
- Account information required: No.
- Use VLAN for internet access: off.
- Apply and restart the ONT/modem.
eero / Nest
- eero app → Settings → Network settings → ISP settings: leave on automatic/DHCP.
- Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: DHCP.
Instant verdict for your router:eero 6+Deco X50/X55ASUS RT-AX86U ProArcher BE550Orbi RBK760Nest Wifi ProOther router
Telstra nbn FTTN / FTTB — VDSL2 BYO modem-router
- Own-router path
- Own router connects directly
- Physical handoff
- FTTN/FTTB copper last mile → VDSL2 modem-router
- WAN connection
- DHCP
- VLAN
- None — untagged
- ISP phone / voice
- Check with your provider
- ISP TV
- No dependency documented
- Evidence confidence
- High — official provider source
Settings to enter on your router
- Use IPoE/DHCP/Automatic.
- Leave VLAN tagging blank/off/0.
- Use VDSL2 Profile 17a with SRA, G.Vector and G.INP as documented by Telstra.
Copy-paste router configuration
Generated from the settings above. Menu names vary by firmware version.
UniFi
- Settings → Internet → select the WAN (Primary) → Advanced: Manual.
- VLAN ID: off.
- IPv4 connection: DHCP.
- Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
- Use the physical WAN NIC as WAN.
- WAN → IPv4 configuration type: DHCP.
- Save, apply, then power-cycle the ONT/modem.
ASUS
- WAN → Internet Connection → WAN Connection Type: Automatic IP.
- LAN → IPTV: leave ISP Profile on None.
- Apply and reboot the ONT/modem.
TP-Link
- Advanced → Network → Internet: connection type Dynamic IP.
- IPTV/VLAN: leave disabled.
- Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
- Save and restart the ONT/modem.
FRITZ!Box
- Internet → Account Information → Internet service provider: Other Internet service provider.
- Connection: via DSL (VDSL).
- Account information required: No.
- Use VLAN for internet access: off.
- Apply and restart the ONT/modem.
eero / Nest
- eero app → Settings → Network settings → ISP settings: leave on automatic/DHCP.
- Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: DHCP.
Instant verdict for your router:eero 6+Deco X50/X55ASUS RT-AX86U ProArcher BE550Orbi RBK760Nest Wifi ProOther router
Other Australian ISPs:Aussie BroadbandOptusTPGiiNetInternodeVodafone AustraliaLeaptelDodoBelongOriginSwoopTangerineSpinTelMATEMoreCompare all Australian ISP settings
Connection type comes before router brand
On FTTC the nbn connection box terminates the DSL side, so an Ethernet router can sit behind it. On FTTN/FTTB the BYO device itself connects to the phone/DSL socket and must contain the VDSL2 modem.
Telstra documents additional VDSL parameters
For FTTN/FTTB, Telstra lists SRA, Profile 17a, G.Vector and G.INP. That is why Hlonix checks more than a generic 'has DSL port' box.
Phone service can change the equipment decision
Telstra distinguishes Internet Only plans from plans with home phone features. If phone service matters, verify the plan-specific equipment path rather than assuming internet-only BYO guidance covers it.
Next step
Evidence
- Telstra — check BYO modem compatibility (official ISP)
- Telstra — nbn settings for third-party equipment (official ISP)
- Telstra — set up a BYO modem/router (official ISP)
Page reviewed 6 November 2026 · compatibility dataset snapshot 23 September 2026.