Australia · Internode
Can I use my own router with Internode?
Yes. Internode documents PPPoE on VLAN 2 with your account's broadband login. Check phone and TV services before you remove the provider box.

Quick reference
Own-router settings at a glance
From official provider sources cited below. Pick your router for a full verdict with topology and caveats.
Internode nbn FTTP / HFC / FTTC / Wireless — own router
- Own-router path
- Own router connects directly
- Physical handoff
- nbn connection box (NTD) → Ethernet WAN
- WAN connection
- PPPoE
- VLAN
- VLAN 2 (802.1Q tagged)
- ISP phone / voice
- Check with your provider
- ISP TV
- Check with your provider
- Evidence confidence
- High — official provider source
Settings to enter on your router
- Connect the router WAN port to the nbn connection box (Ethernet WAN).
- Enable 802.1q VLAN tagging on the WAN with VLAN ID 2 (all new customers; HFC/FTTC always).
- Choose PPPoE with CHAP or PAP authentication.
- Enter username@internode.on.net and the password from your welcome pack.
Copy-paste router configuration
Generated from the settings above. Use the broadband username and password from your provider account or welcome email. Menu names vary by firmware version.
OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan.2'
uci set network.wan.proto='pppoe'
uci set network.wan.username='YOUR_BROADBAND_USERNAME'
uci set network.wan.password='YOUR_BROADBAND_PASSWORD'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restartMikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/interface vlan add name=wan-vlan2 vlan-id=2 interface=ether1
/interface pppoe-client add name=pppoe-out1 interface=wan-vlan2 user="YOUR_BROADBAND_USERNAME" password="YOUR_BROADBAND_PASSWORD" add-default-route=yes use-peer-dns=yes disabled=no
/interface list member add list=WAN interface=pppoe-out1UniFi
- Settings → Internet → select the WAN (Primary) → Advanced: Manual.
- VLAN ID: on, 2.
- IPv4 connection: PPPoE — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
- Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
- Interfaces → VLANs (OPNsense: Interfaces → Other Types → VLAN): parent = WAN NIC, tag 2, priority 0.
- Interfaces → Assignments: assign the new VLAN as WAN.
- WAN → IPv4 configuration type: PPPoE, username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
- Save, apply, then power-cycle the ONT/modem.
ASUS
- WAN → Internet Connection → WAN Connection Type: PPPoE; enter username YOUR_BROADBAND_USERNAME and password YOUR_BROADBAND_PASSWORD.
- LAN → IPTV → Select ISP Profile: Manual → Internet: VID 2, PRIO 0.
- Apply and reboot the ONT/modem.
TP-Link
- Advanced → Network → Internet: connection type PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD).
- Advanced → Network → IPTV/VLAN: enable, Mode Custom, Internet VLAN ID 2.
- Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
- Save and restart the ONT/modem.
FRITZ!Box
- Internet → Account Information → Internet service provider: Other Internet service provider.
- Connection: external modem or router (LAN 1 as WAN).
- Account information required: Yes — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
- Use VLAN for internet access: on, VLAN ID 2.
- Apply and restart the ONT/modem.
eero / Nest
- eero app → Settings → Network settings → ISP settings: PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD); VLAN ID 2.
- Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: PPPoE; VLAN 2 where your firmware offers it.
Instant verdict for your router:eero 6+Deco X50/X55ASUS RT-AX86U ProArcher BE550Orbi RBK760Nest Wifi ProOther router
Internode nbn FTTN / FTTB — own VDSL2 modem
- Own-router path
- Own router connects directly
- Physical handoff
- Phone wall socket → VDSL2 (DSL port)
- WAN connection
- PPPoE
- VLAN
- VLAN 2 (802.1Q tagged)
- ISP phone / voice
- Check with your provider
- ISP TV
- Check with your provider
- Evidence confidence
- High — official provider source
Settings to enter on your router
- Connect the modem's DSL port to the phone socket and select VDSL2 Annex B with vectoring.
- Allow profiles 17a and 30a and enable G.INP, G.Vector and SRA (SOS/ROC if supported).
- Tag the WAN with 802.1q VLAN ID 2 (new customers; some existing customers use none).
- Choose PPPoE (CHAP/PAP) and enter username@internode.on.net and your password.
Copy-paste router configuration
Generated from the settings above. Use the broadband username and password from your provider account or welcome email. Menu names vary by firmware version.
UniFi
- Settings → Internet → select the WAN (Primary) → Advanced: Manual.
- VLAN ID: on, 2.
- IPv4 connection: PPPoE — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
- Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
- Interfaces → VLANs (OPNsense: Interfaces → Other Types → VLAN): parent = WAN NIC, tag 2, priority 0.
- Interfaces → Assignments: assign the new VLAN as WAN.
- WAN → IPv4 configuration type: PPPoE, username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
- Save, apply, then power-cycle the ONT/modem.
ASUS
- WAN → Internet Connection → WAN Connection Type: PPPoE; enter username YOUR_BROADBAND_USERNAME and password YOUR_BROADBAND_PASSWORD.
- LAN → IPTV → Select ISP Profile: Manual → Internet: VID 2, PRIO 0.
- Apply and reboot the ONT/modem.
TP-Link
- Advanced → Network → Internet: connection type PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD).
- Advanced → Network → IPTV/VLAN: enable, Mode Custom, Internet VLAN ID 2.
- Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
- Save and restart the ONT/modem.
FRITZ!Box
- Internet → Account Information → Internet service provider: Other Internet service provider.
- Connection: via DSL (VDSL).
- Account information required: Yes — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
- Use VLAN for internet access: on, VLAN ID 2.
- Apply and restart the ONT/modem.
eero / Nest
- eero app → Settings → Network settings → ISP settings: PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD); VLAN ID 2.
- Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: PPPoE; VLAN 2 where your firmware offers it.
Instant verdict for your router:eero 6+Deco X50/X55ASUS RT-AX86U ProArcher BE550Orbi RBK760Nest Wifi ProOther router
Other Australian ISPs:TelstraAussie BroadbandOptusTPGiiNetVodafone AustraliaLeaptelDodoBelongOriginSwoopTangerineSpinTelMATEMoreCompare all Australian ISP settings
What Internode officially documents
Connect the router WAN port to the nbn connection box (Ethernet WAN). Enable 802.1q VLAN tagging on the WAN with VLAN ID 2 (all new customers; HFC/FTTC always). Choose PPPoE with CHAP or PAP authentication. Enter username@internode.on.net and the password from your welcome pack. Connect the modem's DSL port to the phone socket and select VDSL2 Annex B with vectoring. Allow profiles 17a and 30a and enable G.INP, G.Vector and SRA (SOS/ROC if supported). Tag the WAN with 802.1q VLAN ID 2 (new customers; some existing customers use none). Choose PPPoE (CHAP/PAP) and enter username@internode.on.net and your password.
Before you remove the Internode box
The official page does not settle phone service for a third-party router — confirm before you disconnect the provider box. TV services may use their own VLAN or box; check before swapping. MTU and priority not stated. Some existing FTTP/Wireless customers use no VLAN; HFC/FTTC use VLAN 2 for everyone. NodePhone VoIP: SIP server sip.internode.on.net port 5060, username is your NodePhone number. No page date (footer © 2026).
Common setup mistakes
Choose PPPoE, not Dynamic IP — the line will not come up with DHCP alone. Tag the WAN with VLAN 2; a missing or wrong tag is the most common reason a new router gets no connection. Username format username@internode.on.net; CHAP or PAP Power-cycle the ONT or modem after swapping routers so it releases the old session.
Next step
Evidence
- Internode — General settings / config (official support) (official ISP)
Page reviewed 6 November 2026 · profile researched 6 November 2026.