HHLONIX
EN

Australia · TPG

Can I use my own router with TPG?

Yes. TPG documents PPPoE with no VLAN tag with your account's broadband login. Check phone and TV services before you remove the provider box.

Ethernet cable and network connections
Illustrative photograph; equipment and compatibility may differ.Tony Webster · CC BY 2.0 · Wikimedia Commons
Page reviewed 6 November 2026Profile researched 6 November 2026Cited sources 1How Hlonix verifies →

Quick reference

Own-router settings at a glance

From official provider sources cited below. Pick your router for a full verdict with topology and caveats.

TPG nbn FTTP / HFC / FTTC / Wireless — own router

Own-router path
Own router connects directly
Physical handoff
nbn connection box (NTD) → Ethernet WAN
WAN connection
PPPoE
VLAN
None — untagged
ISP phone / voice
Check with your provider
ISP TV
Check with your provider
Evidence confidence
High — official provider source

Settings to enter on your router

  1. Connect the router WAN port to the nbn connection box.
  2. Set the connection type to PPPoE; if the router has an ISP list, pick 'Other' rather than 'TPG'.
  3. Enter your full TPG username in the form username@tpg.com.au and your account password.
  4. For a BYO / unbundled service on HFC, FTTC or Wireless, keep VLAN off (FTTP lists no VLAN).
  5. Optionally set DNS to 203.12.160.35 and 203.12.160.36.

Copy-paste router configuration

Generated from the settings above. Use the broadband username and password from your provider account or welcome email. Menu names vary by firmware version.

OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan'
uci set network.wan.proto='pppoe'
uci set network.wan.username='YOUR_BROADBAND_USERNAME'
uci set network.wan.password='YOUR_BROADBAND_PASSWORD'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restart
MikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/interface pppoe-client add name=pppoe-out1 interface=ether1 user="YOUR_BROADBAND_USERNAME" password="YOUR_BROADBAND_PASSWORD" add-default-route=yes use-peer-dns=yes disabled=no
/interface list member add list=WAN interface=pppoe-out1
UniFi
  1. Settings → Internet → select the WAN (Primary) → Advanced: Manual.
  2. VLAN ID: off.
  3. IPv4 connection: PPPoE — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
  4. Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
  1. Use the physical WAN NIC as WAN.
  2. WAN → IPv4 configuration type: PPPoE, username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
  3. Save, apply, then power-cycle the ONT/modem.
ASUS
  1. WAN → Internet Connection → WAN Connection Type: PPPoE; enter username YOUR_BROADBAND_USERNAME and password YOUR_BROADBAND_PASSWORD.
  2. LAN → IPTV: leave ISP Profile on None.
  3. Apply and reboot the ONT/modem.
TP-Link
  1. Advanced → Network → Internet: connection type PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD).
  2. IPTV/VLAN: leave disabled.
  3. Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
  4. Save and restart the ONT/modem.
FRITZ!Box
  1. Internet → Account Information → Internet service provider: Other Internet service provider.
  2. Connection: external modem or router (LAN 1 as WAN).
  3. Account information required: Yes — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
  4. Use VLAN for internet access: off.
  5. Apply and restart the ONT/modem.
eero / Nest
  1. eero app → Settings → Network settings → ISP settings: PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD).
  2. Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: PPPoE.

TPG nbn FTTN / FTTB — own VDSL2 modem

Own-router path
Own router connects directly
Physical handoff
Phone wall socket → VDSL2 (DSL port)
WAN connection
PPPoE
VLAN
None — untagged
ISP phone / voice
Check with your provider
ISP TV
Check with your provider
Evidence confidence
High — official provider source

Settings to enter on your router

  1. Connect the VDSL2 modem's DSL port to the phone wall socket.
  2. Select VDSL2 with profile 17a (multimode) and PTM as the transfer mode; enable G.INP, G.Vector and SOS/ROC (update firmware if missing).
  3. Choose PPPoE and enter username@tpg.com.au plus your account password.
  4. BYO/unbundled: VLAN off. Bundled nbn + phone: VLAN on, ID 2, priority 0.

Copy-paste router configuration

Generated from the settings above. Use the broadband username and password from your provider account or welcome email. Menu names vary by firmware version.

UniFi
  1. Settings → Internet → select the WAN (Primary) → Advanced: Manual.
  2. VLAN ID: off.
  3. IPv4 connection: PPPoE — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
  4. Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
  1. Use the physical WAN NIC as WAN.
  2. WAN → IPv4 configuration type: PPPoE, username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
  3. Save, apply, then power-cycle the ONT/modem.
ASUS
  1. WAN → Internet Connection → WAN Connection Type: PPPoE; enter username YOUR_BROADBAND_USERNAME and password YOUR_BROADBAND_PASSWORD.
  2. LAN → IPTV: leave ISP Profile on None.
  3. Apply and reboot the ONT/modem.
TP-Link
  1. Advanced → Network → Internet: connection type PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD).
  2. IPTV/VLAN: leave disabled.
  3. Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
  4. Save and restart the ONT/modem.
FRITZ!Box
  1. Internet → Account Information → Internet service provider: Other Internet service provider.
  2. Connection: via DSL (VDSL).
  3. Account information required: Yes — username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD.
  4. Use VLAN for internet access: off.
  5. Apply and restart the ONT/modem.
eero / Nest
  1. eero app → Settings → Network settings → ISP settings: PPPoE (username YOUR_BROADBAND_USERNAME, password YOUR_BROADBAND_PASSWORD).
  2. Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: PPPoE.
WAN authPPPoE
VLANNone — untagged
Priority / PCP—
MTUDefault

What TPG officially documents

Connect the router WAN port to the nbn connection box. Set the connection type to PPPoE; if the router has an ISP list, pick 'Other' rather than 'TPG'. Enter your full TPG username in the form username@tpg.com.au and your account password. For a BYO / unbundled service on HFC, FTTC or Wireless, keep VLAN off (FTTP lists no VLAN). Optionally set DNS to 203.12.160.35 and 203.12.160.36. Connect the VDSL2 modem's DSL port to the phone wall socket. Select VDSL2 with profile 17a (multimode) and PTM as the transfer mode; enable G.INP, G.Vector and SOS/ROC (update firmware if missing). Choose PPPoE and enter username@tpg.com.au plus your account password. BYO/unbundled: VLAN off. Bundled nbn + phone: VLAN on, ID 2, priority 0.

Before you remove the TPG box

The official page does not settle phone service for a third-party router — confirm before you disconnect the provider box. TV services may use their own VLAN or box; check before swapping. MTU not stated. On bundled nbn + phone plans TPG lists VLAN on, ID 2, 802.1p priority 0 for HFC/FTTC/Wireless; BYO/unbundled uses VLAN off. Home Wireless Broadband and 5G Home Broadband do not support BYO. TPG's own FTTH network also uses PPPoE with the same username format. No page date.

Common setup mistakes

Choose PPPoE, not Dynamic IP — the line will not come up with DHCP alone. Leave WAN VLAN tagging off; adding a tag here breaks the connection. Username format username@tpg.com.au; DNS 203.12.160.35 / 203.12.160.36 Power-cycle the ONT or modem after swapping routers so it releases the old session.

Next step

Evidence

Page reviewed 6 November 2026 · profile researched 6 November 2026.