Australia · Origin
Can I use my own router with Origin?
Yes. Origin documents DHCP / IPoE with no VLAN tag. Check phone and TV services before you remove the provider box.

Quick reference
Own-router settings at a glance
From official provider sources cited below. Pick your router for a full verdict with topology and caveats.
Origin nbn FTTP / FTTC / HFC / Fixed Wireless — own modem
- Own-router path
- Own router connects directly
- Physical handoff
- nbn connection box (NTD) → Ethernet WAN
- WAN connection
- DHCP
- VLAN
- None — untagged
- ISP phone / voice
- Check with your provider
- ISP TV
- Check with your provider
- Evidence confidence
- Medium — verify account details
Settings to enter on your router
- Connect the modem's WAN port to the nbn connection box and set the mode to Ethernet WAN (on TP-Link, use Wireless Router mode if offered).
- Set IP addressing to automatic (Dynamic / IPoE / DHCP).
- Set VLAN ID to none.
- FTTN/FTTB: set DSL mode to VDSL, connection Dynamic/IPoE/DHCP, no VLAN, enable SRA if available; no ISP username or password needed.
Copy-paste router configuration
Generated from the settings above. Menu names vary by firmware version.
OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan'
uci set network.wan.proto='dhcp'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restartMikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/ip dhcp-client add interface=ether1 disabled=noUniFi
- Settings → Internet → select the WAN (Primary) → Advanced: Manual.
- VLAN ID: off.
- IPv4 connection: DHCP.
- Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
- Use the physical WAN NIC as WAN.
- WAN → IPv4 configuration type: DHCP.
- Save, apply, then power-cycle the ONT/modem.
ASUS
- WAN → Internet Connection → WAN Connection Type: Automatic IP.
- LAN → IPTV: leave ISP Profile on None.
- Apply and reboot the ONT/modem.
TP-Link
- Advanced → Network → Internet: connection type Dynamic IP.
- IPTV/VLAN: leave disabled.
- Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
- Save and restart the ONT/modem.
FRITZ!Box
- Internet → Account Information → Internet service provider: Other Internet service provider.
- Connection: external modem or router (LAN 1 as WAN).
- Account information required: No.
- Use VLAN for internet access: off.
- Apply and restart the ONT/modem.
eero / Nest
- eero app → Settings → Network settings → ISP settings: leave on automatic/DHCP.
- Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: DHCP.
Instant verdict for your router:eero 6+Deco X50/X55ASUS RT-AX86U ProArcher BE550Orbi RBK760Nest Wifi ProOther router
Other Australian ISPs:TelstraAussie BroadbandOptusTPGiiNetInternodeVodafone AustraliaLeaptelDodoBelongSwoopTangerineSpinTelMATEMoreCompare all Australian ISP settings
What Origin officially documents
Connect the modem's WAN port to the nbn connection box and set the mode to Ethernet WAN (on TP-Link, use Wireless Router mode if offered). Set IP addressing to automatic (Dynamic / IPoE / DHCP). Set VLAN ID to none. FTTN/FTTB: set DSL mode to VDSL, connection Dynamic/IPoE/DHCP, no VLAN, enable SRA if available; no ISP username or password needed.
Before you remove the Origin box
The official page does not settle phone service for a third-party router — confirm before you disconnect the provider box. TV services may use their own VLAN or box; check before swapping. Article dated 13 Sep 2024. For FTTP/FTTC/HFC/FW the connection type is not named explicitly, but IP is automatic and VLAN none; FTTN/FTTB explicitly IPoE/DHCP with no login. MTU and VoIP not stated.
Common setup mistakes
Choose Dynamic IP / DHCP (IPoE), not PPPoE — there is no broadband login to enter. Leave WAN VLAN tagging off; adding a tag here breaks the connection. IP address automatic Power-cycle the ONT or modem after swapping routers so it releases the old session.
Next step
Evidence
Page reviewed 6 November 2026 · profile researched 6 November 2026.