HHLONIX
EN

Australia · Optus

Can I use my own router with Optus?

Yes. Optus documents DHCP / IPoE with no VLAN tag. Check phone and TV services before you remove the provider box.

Network equipment and server rack
Illustrative photograph; equipment and compatibility may differ.Shixart1985 · CC BY 2.0 · Wikimedia Commons
Page reviewed 6 November 2026Profile researched 6 November 2026Cited sources 1How Hlonix verifies →

Quick reference

Own-router settings at a glance

From official provider sources cited below. Pick your router for a full verdict with topology and caveats.

Optus nbn FTTP / HFC / FTTC / Fixed Wireless — own router

Own-router path
Own router connects directly
Physical handoff
nbn connection box (NTD) → Ethernet WAN
WAN connection
DHCP
VLAN
None — untagged
ISP phone / voice
Check with your provider
ISP TV
Check with your provider
Evidence confidence
High — official provider source

Settings to enter on your router

  1. Plug the router's WAN port into the UNI-D port of the nbn connection box with an Ethernet cable.
  2. Choose Ethernet WAN as the connection type and IPoE (DHCP client / Dynamic IP) as the internet type.
  3. Turn VLAN tagging off (Optus lists VLAN as disabled/none).
  4. Leave the username and password fields empty; Optus nbn uses no PPPoE login.
  5. Save, then power-cycle the router (unplug for about 60 seconds) if it does not come online.

Copy-paste router configuration

Generated from the settings above. Menu names vary by firmware version.

OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan'
uci set network.wan.proto='dhcp'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restart
MikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/ip dhcp-client add interface=ether1 disabled=no
UniFi
  1. Settings → Internet → select the WAN (Primary) → Advanced: Manual.
  2. VLAN ID: off.
  3. IPv4 connection: DHCP.
  4. Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
  1. Use the physical WAN NIC as WAN.
  2. WAN → IPv4 configuration type: DHCP.
  3. Save, apply, then power-cycle the ONT/modem.
ASUS
  1. WAN → Internet Connection → WAN Connection Type: Automatic IP.
  2. LAN → IPTV: leave ISP Profile on None.
  3. Apply and reboot the ONT/modem.
TP-Link
  1. Advanced → Network → Internet: connection type Dynamic IP.
  2. IPTV/VLAN: leave disabled.
  3. Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
  4. Save and restart the ONT/modem.
FRITZ!Box
  1. Internet → Account Information → Internet service provider: Other Internet service provider.
  2. Connection: external modem or router (LAN 1 as WAN).
  3. Account information required: No.
  4. Use VLAN for internet access: off.
  5. Apply and restart the ONT/modem.
eero / Nest
  1. eero app → Settings → Network settings → ISP settings: leave on automatic/DHCP.
  2. Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: DHCP.

Optus nbn FTTN / FTTB — own VDSL2 modem-router

Own-router path
Own router connects directly
Physical handoff
Phone wall socket → VDSL2 (DSL port)
WAN connection
DHCP
VLAN
None — untagged
ISP phone / voice
Check with your provider
ISP TV
Check with your provider
Evidence confidence
High — official provider source

Settings to enter on your router

  1. Connect the modem's DSL port to the main phone wall socket.
  2. Select VDSL2 Annex B with vectoring; allow profiles 17a and 30a.
  3. Enable G.INP (G.998.4), G.Vector (G.993.5), SRA and SOS/ROC.
  4. Set the internet connection to IPoE with DHCP client, VLAN disabled.
  5. Leave username and password blank.

Copy-paste router configuration

Generated from the settings above. Menu names vary by firmware version.

UniFi
  1. Settings → Internet → select the WAN (Primary) → Advanced: Manual.
  2. VLAN ID: off.
  3. IPv4 connection: DHCP.
  4. Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
  1. Use the physical WAN NIC as WAN.
  2. WAN → IPv4 configuration type: DHCP.
  3. Save, apply, then power-cycle the ONT/modem.
ASUS
  1. WAN → Internet Connection → WAN Connection Type: Automatic IP.
  2. LAN → IPTV: leave ISP Profile on None.
  3. Apply and reboot the ONT/modem.
TP-Link
  1. Advanced → Network → Internet: connection type Dynamic IP.
  2. IPTV/VLAN: leave disabled.
  3. Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
  4. Save and restart the ONT/modem.
FRITZ!Box
  1. Internet → Account Information → Internet service provider: Other Internet service provider.
  2. Connection: via DSL (VDSL).
  3. Account information required: No.
  4. Use VLAN for internet access: off.
  5. Apply and restart the ONT/modem.
eero / Nest
  1. eero app → Settings → Network settings → ISP settings: leave on automatic/DHCP.
  2. Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: DHCP.
WAN authDHCP / IPoE
VLANNone — untagged
Priority / PCP—
MTUDefault

What Optus officially documents

Plug the router's WAN port into the UNI-D port of the nbn connection box with an Ethernet cable. Choose Ethernet WAN as the connection type and IPoE (DHCP client / Dynamic IP) as the internet type. Turn VLAN tagging off (Optus lists VLAN as disabled/none). Leave the username and password fields empty; Optus nbn uses no PPPoE login. Save, then power-cycle the router (unplug for about 60 seconds) if it does not come online. Connect the modem's DSL port to the main phone wall socket. Select VDSL2 Annex B with vectoring; allow profiles 17a and 30a. Enable G.INP (G.998.4), G.Vector (G.993.5), SRA and SOS/ROC. Set the internet connection to IPoE with DHCP client, VLAN disabled. Leave username and password blank.

Before you remove the Optus box

The official page does not settle phone service for a third-party router — confirm before you disconnect the provider box. TV services may use their own VLAN or box; check before swapping. MTU and voice settings not stated. Optus says support for non-Optus modems is limited and recommends a modem under five years old. Page shows no date (footer © 2026).

Common setup mistakes

Choose Dynamic IP / DHCP (IPoE), not PPPoE — there is no broadband login to enter. Leave WAN VLAN tagging off; adding a tag here breaks the connection. Same IPoE/DHCP settings apply to FTTP, HFC, FTTC and Fixed Wireless Power-cycle the ONT or modem after swapping routers so it releases the old session.

Next step

Evidence

Page reviewed 6 November 2026 · profile researched 6 November 2026.