HHLONIX
EN

Australia · Swoop

Can I use my own router with Swoop?

Yes. Swoop documents DHCP / IPoE with no VLAN tag. Check phone and TV services before you remove the provider box.

Ethernet cable and network connections
Illustrative photograph; equipment and compatibility may differ.Amin · CC BY-SA 4.0 · Wikimedia Commons
Page reviewed 6 November 2026Profile researched 6 November 2026Cited sources 1How Hlonix verifies →

Quick reference

Own-router settings at a glance

From official provider sources cited below. Pick your router for a full verdict with topology and caveats.

Swoop nbn FTTP / FTTC / HFC / Wireless — own modem

Own-router path
Own router connects directly
Physical handoff
nbn connection box (NTD) → Ethernet WAN
WAN connection
DHCP
VLAN
None — untagged
ISP phone / voice
Check with your provider
ISP TV
Check with your provider
Evidence confidence
Medium — verify account details

Settings to enter on your router

  1. Connect the modem's Ethernet WAN (EWAN) port to the nbn connection box.
  2. In the EWAN settings choose Dynamic IP (IPoE) — or PPPoE if you prefer.
  3. Keep VLAN disabled.
  4. Only for PPPoE: enter your Swoop internet username and password; skip this for IPoE.

Copy-paste router configuration

Generated from the settings above. Menu names vary by firmware version.

OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan'
uci set network.wan.proto='dhcp'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restart
MikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/ip dhcp-client add interface=ether1 disabled=no
UniFi
  1. Settings → Internet → select the WAN (Primary) → Advanced: Manual.
  2. VLAN ID: off.
  3. IPv4 connection: DHCP.
  4. Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
  1. Use the physical WAN NIC as WAN.
  2. WAN → IPv4 configuration type: DHCP.
  3. Save, apply, then power-cycle the ONT/modem.
ASUS
  1. WAN → Internet Connection → WAN Connection Type: Automatic IP.
  2. LAN → IPTV: leave ISP Profile on None.
  3. Apply and reboot the ONT/modem.
TP-Link
  1. Advanced → Network → Internet: connection type Dynamic IP.
  2. IPTV/VLAN: leave disabled.
  3. Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
  4. Save and restart the ONT/modem.
FRITZ!Box
  1. Internet → Account Information → Internet service provider: Other Internet service provider.
  2. Connection: external modem or router (LAN 1 as WAN).
  3. Account information required: No.
  4. Use VLAN for internet access: off.
  5. Apply and restart the ONT/modem.
eero / Nest
  1. eero app → Settings → Network settings → ISP settings: leave on automatic/DHCP.
  2. Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: DHCP.
WAN authDHCP / IPoE
VLANNone — untagged
Priority / PCP—
MTUDefault

What Swoop officially documents

Connect the modem's Ethernet WAN (EWAN) port to the nbn connection box. In the EWAN settings choose Dynamic IP (IPoE) — or PPPoE if you prefer. Keep VLAN disabled. Only for PPPoE: enter your Swoop internet username and password; skip this for IPoE.

Before you remove the Swoop box

The official page does not settle phone service for a third-party router — confirm before you disconnect the provider box. TV services may use their own VLAN or box; check before swapping. Taken from Swoop's official model-specific BYO guide (TP-Link Archer VX420, last modified 27 Aug 2024); Swoop publishes similar guides per model and per technology. MTU and VoIP not stated.

Common setup mistakes

Choose Dynamic IP / DHCP (IPoE), not PPPoE — there is no broadband login to enter. Leave WAN VLAN tagging off; adding a tag here breaks the connection. PPPoE also supported (then account-specific username/password) Power-cycle the ONT or modem after swapping routers so it releases the old session.

Next step

Evidence

Page reviewed 6 November 2026 · profile researched 6 November 2026.