United States · altafiber (Fioptics)
Can I use my own router with altafiber (Fioptics)?
Yes. altafiber (Fioptics) documents DHCP / IPoE with no VLAN tag. Check phone and TV services before you remove the provider box.

Quick reference
Own-router settings at a glance
From official provider sources cited below. Pick your router for a full verdict with topology and caveats.
altafiber Fioptics — customer-owned gateway on the ONT (DHCP)
- Own-router path
- Own router connects directly
- Physical handoff
- Fibre ONT (port 1) or Fioptics data jack → Ethernet WAN
- WAN connection
- DHCP
- VLAN
- None — untagged
- ISP phone / voice
- Check with your provider
- ISP TV
- Check with your provider
- Evidence confidence
- High — official provider source
Settings to enter on your router
- Use a router/gateway with a Gigabit Ethernet WAN port (needed for plans above 100 Mbps) and Cat5e/Cat6 cable.
- Connect the router's WAN port to the Fioptics data jack (blue/orange port) or directly to port 1 on the ONT.
- Set the WAN connection type to DHCP (dynamic IP); no VLAN or login is listed in altafiber's spec.
- Keep NAT enabled on the router and use a private LAN range for your devices.
Copy-paste router configuration
Generated from the settings above. Menu names vary by firmware version.
OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan'
uci set network.wan.proto='dhcp'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restartMikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/ip dhcp-client add interface=ether1 disabled=noUniFi
- Settings → Internet → select the WAN (Primary) → Advanced: Manual.
- VLAN ID: off.
- IPv4 connection: DHCP.
- Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
- Use the physical WAN NIC as WAN.
- WAN → IPv4 configuration type: DHCP.
- Save, apply, then power-cycle the ONT/modem.
ASUS
- WAN → Internet Connection → WAN Connection Type: Automatic IP.
- LAN → IPTV: leave ISP Profile on None.
- Apply and reboot the ONT/modem.
TP-Link
- Advanced → Network → Internet: connection type Dynamic IP.
- IPTV/VLAN: leave disabled.
- Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
- Save and restart the ONT/modem.
FRITZ!Box
- Internet → Account Information → Internet service provider: Other Internet service provider.
- Connection: external modem or router (LAN 1 as WAN).
- Account information required: No.
- Use VLAN for internet access: off.
- Apply and restart the ONT/modem.
eero / Nest
- eero app → Settings → Network settings → ISP settings: leave on automatic/DHCP.
- Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: DHCP.
Instant verdict for your router:eero 6+Deco X50/X55ASUS RT-AX86U ProArcher BE550Orbi RBK760Nest Wifi ProOther router
Other US ISPs:AT&TXfinityGFiberSpectrumVerizon FiosCenturyLinkQuantum FiberFrontierCoxOptimumZiply FiberSonicMetronetBrightspeedKinetic (Windstream)T-Mobile Home InternetVerizon 5G HomeAstound Broadband (RCN / Wave / Grande)MediacomWOW!EPBCompare all US ISP settings
What altafiber (Fioptics) officially documents
Use a router/gateway with a Gigabit Ethernet WAN port (needed for plans above 100 Mbps) and Cat5e/Cat6 cable. Connect the router's WAN port to the Fioptics data jack (blue/orange port) or directly to port 1 on the ONT. Set the WAN connection type to DHCP (dynamic IP); no VLAN or login is listed in altafiber's spec. Keep NAT enabled on the router and use a private LAN range for your devices.
Before you remove the altafiber (Fioptics) box
The official page does not settle phone service for a third-party router — confirm before you disconnect the provider box. TV services may use their own VLAN or box; check before swapping. altafiber's customer-owned gateway spec lists DHCP + NAT only; VLAN is not mentioned (treated as none — confirm if it fails). Static-IP customers can get a secondary public IPv4 subnet for a fee. Separate Bring-Your-Own-Gateway terms and conditions exist (not reviewed).
Common setup mistakes
Choose Dynamic IP / DHCP (IPoE), not PPPoE — there is no broadband login to enter. Leave WAN VLAN tagging off; adding a tag here breaks the connection. Dynamic IPv4 via DHCP; NAT must be enabled; Gigabit WAN port needed above 100 Mbps; gateway within 300 ft of the ONT. VLAN, MTU and IPv6 not stated. Power-cycle the ONT or modem after swapping routers so it releases the old session.
Next step
Evidence
- altafiber — Customer-Owned Gateway specification and configuration guidelines (official PDF) (official ISP)
- altafiber — Customer-provided gateway self-install instructions (official PDF) (official ISP)
Page reviewed 6 November 2026 · profile researched 6 November 2026.