United States · Verizon Fios
Can I use my own router with Verizon Fios?
For a modern internet-only Fios setup using Ethernet from the ONT, Verizon-hosted community guidance documents using a third-party router. Hlonix keeps the verdict at medium confidence because that specific own-router procedure is community guidance rather than a standard Verizon support article.

Quick reference
Own-router settings at a glance
From official provider sources cited below. Pick your router for a full verdict with topology and caveats.
Verizon Fios — internet-only own router via ONT
- Own-router path
- Own router connects directly (medium-confidence evidence)
- Physical handoff
- Fios ONT → Ethernet WAN
- WAN connection
- DHCP
- VLAN
- None — untagged
- ISP phone / voice
- Check with your provider
- ISP TV
- Provider hub required
- Evidence confidence
- Medium — verify account details
Settings to enter on your router
- For standalone Fios Internet, a third-party router can use the ONT Ethernet handoff.
- Keep Verizon equipment if your TV setup requires it or if your installation uses legacy coax/MoCA routing.
- Third-party-router support is limited; Hlonix therefore keeps this profile at medium confidence.
Copy-paste router configuration
Generated from the settings above. Menu names vary by firmware version.
OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan'
uci set network.wan.proto='dhcp'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restartMikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/ip dhcp-client add interface=ether1 disabled=noUniFi
- Settings → Internet → select the WAN (Primary) → Advanced: Manual.
- VLAN ID: off.
- IPv4 connection: DHCP.
- Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
- Use the physical WAN NIC as WAN.
- WAN → IPv4 configuration type: DHCP.
- Save, apply, then power-cycle the ONT/modem.
ASUS
- WAN → Internet Connection → WAN Connection Type: Automatic IP.
- LAN → IPTV: leave ISP Profile on None.
- Apply and reboot the ONT/modem.
TP-Link
- Advanced → Network → Internet: connection type Dynamic IP.
- IPTV/VLAN: leave disabled.
- Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
- Save and restart the ONT/modem.
FRITZ!Box
- Internet → Account Information → Internet service provider: Other Internet service provider.
- Connection: external modem or router (LAN 1 as WAN).
- Account information required: No.
- Use VLAN for internet access: off.
- Apply and restart the ONT/modem.
eero / Nest
- eero app → Settings → Network settings → ISP settings: leave on automatic/DHCP.
- Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: DHCP.
Instant verdict for your router:eero 6+Deco X50/X55ASUS RT-AX86U ProArcher BE550Orbi RBK760Nest Wifi ProOther router
Other US ISPs:AT&TXfinityGFiberSpectrumCenturyLinkQuantum FiberFrontierCoxOptimumZiply FiberSonicMetronetBrightspeedKinetic (Windstream)T-Mobile Home InternetVerizon 5G HomeAstound Broadband (RCN / Wave / Grande)MediacomWOW!altafiber (Fioptics)EPBCompare all US ISP settings
Why the ONT stays
The ONT converts the fiber signal to Ethernet/data service. Replacing the router does not mean removing the ONT.
Why TV changes the answer
The Verizon Community KB explicitly warns that Fios One set-top boxes require a Verizon router as primary. Internet-only and TV bundles therefore should not share one universal verdict.
Evidence limitation
Verizon's official support documents the ONT and Ethernet self-install path, while the own-router procedure itself is in Verizon-hosted community documentation. Hlonix surfaces that distinction instead of hiding it.
Next step
Evidence
- Verizon Community KB — using your own router with Fios (Verizon-hosted community / secondary)
- Verizon — Fios ONT and Ethernet self-install (official ISP)
Page reviewed 6 November 2026 · compatibility dataset snapshot 23 September 2026.