United States · Quantum Fiber
Can I use my own router with Quantum Fiber?
Only behind the provider device. Provider hub/router must stay. Check phone and TV services before you remove the provider box.

Quick reference
Own-router settings at a glance
From official provider sources cited below. Pick your router for a full verdict with topology and caveats.
Quantum Fiber — own router behind the Quantum modem / SmartNID
- Own-router path
- Provider hub/router must stay
- Physical handoff
- Fibre → Quantum Fiber modem or SmartNID → your router (Ethernet)
- WAN connection
- Handled by the provider gateway
- VLAN
- Handled by provider device
- ISP phone / voice
- Check with your provider
- ISP TV
- No dependency documented
- Evidence confidence
- High — official provider source
Settings to enter on your router
- Connect your router's WAN port by Ethernet to the Quantum Fiber modem (C4000XG) or wall-mounted SmartNID (C5500XK).
- Set the router's WAN/Internet connection type to automatic IP (DHCP) — Quantum lists DHCP for the WAN address as a requirement.
- Use a router with a 1 Gbps Ethernet WAN port (2.5 Gbps for multi-gig plans) and Wi-Fi 5 or better.
- If you only want Wi-Fi from your device, put it in access-point mode and disable its DHCP server — Quantum recommends this to avoid issues with gaming, VPN and voice.
- Leave the SmartNID in place and do not unplug its green fiber wires.
Instant verdict for your router:eero 6+Deco X50/X55ASUS RT-AX86U ProArcher BE550Orbi RBK760Nest Wifi ProOther router
Other US ISPs:AT&TXfinityGFiberSpectrumVerizon FiosCenturyLinkFrontierCoxOptimumZiply FiberSonicMetronetBrightspeedKinetic (Windstream)T-Mobile Home InternetVerizon 5G HomeAstound Broadband (RCN / Wave / Grande)MediacomWOW!altafiber (Fioptics)EPBCompare all US ISP settings
What Quantum Fiber officially documents
Connect your router's WAN port by Ethernet to the Quantum Fiber modem (C4000XG) or wall-mounted SmartNID (C5500XK). Set the router's WAN/Internet connection type to automatic IP (DHCP) — Quantum lists DHCP for the WAN address as a requirement. Use a router with a 1 Gbps Ethernet WAN port (2.5 Gbps for multi-gig plans) and Wi-Fi 5 or better. If you only want Wi-Fi from your device, put it in access-point mode and disable its DHCP server — Quantum recommends this to avoid issues with gaming, VPN and voice. Leave the SmartNID in place and do not unplug its green fiber wires.
Before you remove the Quantum Fiber box
The official page does not settle phone service for a third-party router — confirm before you disconnect the provider box. No TV dependency is documented. Quantum provides no list of compatible third-party fiber modems and does not support replacing its modem/SmartNID; VLAN/PPPoE not stated. Using your own Wi-Fi drops 360 WiFi features and Fiber Customer Success support. C4000/C3000/C3510 gateways cannot be set to AP mode. Site footer now reads © 2026 AT&T (Lumen consumer fiber sold to AT&T).
Common setup mistakes
If the provider device must stay, put your own router behind it and avoid double NAT: use the provider's bridge, modem or passthrough option where one exists, otherwise run your router in access-point mode.
Next step
Evidence
- Quantum Fiber — using your own WiFi equipment (official support) (official ISP)
- Quantum Fiber — equipment and modem FAQs (official support) (official ISP)
Page reviewed 6 November 2026 · profile researched 6 November 2026.