HHLONIX
EN

United States · GFiber

Can I use my own router with Google Fiber / GFiber?

Yes. GFiber currently says customers can use their own router, and its current Wi-Fi guidance says the router can plug directly into the Fiber Jack without enabling bridge mode.

Broadband router hardware
Illustrative photograph; equipment and compatibility may differ.Paul Sableman · CC BY 2.0 · Wikimedia Commons
Page reviewed 6 November 2026Dataset snapshot 23 September 2026Cited sources 1How Hlonix verifies →

Quick reference

Own-router settings at a glance

From official provider sources cited below. Pick your router for a full verdict with topology and caveats.

Google Fiber / GFiber — own router direct to Fiber Jack

Own-router path
Own router connects directly
Physical handoff
GFiber Fiber Jack / ONT → Ethernet WAN
WAN connection
DHCP
VLAN
None — untagged
ISP phone / voice
Check with your provider
ISP TV
No dependency documented
Evidence confidence
High — official provider source

Settings to enter on your router

  1. Connect your own router directly to the Fiber Jack / Ethernet handoff.
  2. No bridge-mode step is needed for the current own-router path described by GFiber.
  3. Choose router port speeds that can actually carry your plan tier.

Copy-paste router configuration

Generated from the settings above. Menu names vary by firmware version.

OpenWrt
# OpenWrt 23.05+ (DSA). WAN port is usually 'wan' (older targets: 'eth1').
uci set network.wan.device='wan'
uci set network.wan.proto='dhcp'
uci set network.wan6.device='@wan'
uci commit network
/etc/init.d/network restart
MikroTik
# RouterOS 7, default config (ether1 = WAN, interface list WAN exists)
/ip dhcp-client add interface=ether1 disabled=no
UniFi
  1. Settings → Internet → select the WAN (Primary) → Advanced: Manual.
  2. VLAN ID: off.
  3. IPv4 connection: DHCP.
  4. Apply, then power-cycle the ONT/modem.
pfSense / OPNsense
  1. Use the physical WAN NIC as WAN.
  2. WAN → IPv4 configuration type: DHCP.
  3. Save, apply, then power-cycle the ONT/modem.
ASUS
  1. WAN → Internet Connection → WAN Connection Type: Automatic IP.
  2. LAN → IPTV: leave ISP Profile on None.
  3. Apply and reboot the ONT/modem.
TP-Link
  1. Advanced → Network → Internet: connection type Dynamic IP.
  2. IPTV/VLAN: leave disabled.
  3. Deco app: More → Advanced → IPTV/VLAN and Internet connection use the same values.
  4. Save and restart the ONT/modem.
FRITZ!Box
  1. Internet → Account Information → Internet service provider: Other Internet service provider.
  2. Connection: external modem or router (LAN 1 as WAN).
  3. Account information required: No.
  4. Use VLAN for internet access: off.
  5. Apply and restart the ONT/modem.
eero / Nest
  1. eero app → Settings → Network settings → ISP settings: leave on automatic/DHCP.
  2. Google Home app (Nest Wifi Pro) → Wi-Fi → Network settings → Advanced networking → WAN: DHCP.
Own routerSupported
Provider box to keepFiber Jack / ONT
Bridge modeNot required for current own-router path
Main hardware limitRouter WAN/LAN speed vs plan tier

This is a true router replacement

The Fiber Jack remains because it is the fiber termination point, but the GFiber router itself does not have to remain in the path for the documented own-router setup.

Multi-gig plans change the hardware question

A router can be protocol-compatible yet bottleneck a 3, 5 or 8 Gig service if its WAN/LAN ports are slower. Hlonix therefore treats physical port capability as a separate buying consideration.

Support boundary

GFiber notes that third-party router support is limited. Keep enough information about your original setup to reconnect provider equipment if troubleshooting requires it.

Next step

Evidence

Page reviewed 6 November 2026 · compatibility dataset snapshot 23 September 2026.